The Intimate Archives: Re: setting up ipaq with new install meth

From: Tim <i2wild.a.t.hotmail.com>
Date: Sat Mar 01 2003 - 16:46:36 EST

Hello;
             Here is more info on this problem.
Initializing aux micro
Flash style = 2x16
queryFlash(0x13) returns 0x00000001
verify flash size...
btflash_init: mfrid=00890089
  devid=00170017
walking flash descriptors (2x16)
btflash_init: found flash 28F640J3A
  flashDescriptor=00035498
  flashSectors=00035394
  nsectors=00000040
  flash_size=01000000
  flash_address_mask=00FFFFFF
no control function
Machine type--> iPAQ 3600
mach_type ->00000016
allocated partition_table
defining partition: bootldr
defining partition: root
initialize_by_mach_type done
probing ram
SDRAM size: 0x02000000
in megs: 32M
Disabling LCD controller
Disabling LCD controller
Enabling LCD controller
before EN
after EN
after EGPIO
DBAR1=C1E436C0
LCCR0=000000B9
LCCR1=0B100930
LCCR2=0A0108F0
LCCR3=00300010
params=0x000359F8
>> Compaq OHH BootLoader, Rev 2-19-58 [BIG_KERNEL] [MD5] [MONO]
>> 03-02-19_17:57
>> Last link date: Wed Feb 19 17:58:00 EST 2003
>> Contact: bootldr@handhelds.org

*MTST
00000001
00000002
00000004
00000008
00000010
00000020
00000040
00000080
00000100
00000200
00000400
00000800
00001000
00002000
00004000
00008000
00010000
00020000
00040000
00080000
00100000
00200000
00400000
00800000
01000000
02000000
04000000
08000000
10000000
20000000
40000000
80000000
MBK2
00000001
E59F18C0
00000002
E59F18C0
00000004
E59F18C0
00000008
E59F18C0
00000010
E59F18C0
00000020
E59F18C0
00000040
E59F18C0
00000080
E59F18C0
00000100
E59F18C0
00000200
E59F18C0
00000400
E59F18C0
00000800
E59F18C0
00001000
E59F18C0
00002000
E59F18C0
00004000
E59F18C0
00008000
E59F18C0
00010000
E59F18C0
00020000
E59F18C0
00040000
E59F18C0
00080000
E59F18C0
00100000
E59F18C0
00200000
E59F18C0
00400000
E59F18C0
00800000
E59F18C0
01000000
E59F18C0
02000000
E59F18C0
04000000
E59F18C0
08000000
E59F18C0
10000000
E59F18C0
20000000
E59F18C0
40000000
E59F18C0
80000000
E59F18C0
ENDM
STKP
C19F3FF0
Initializing aux micro
Flash style = 2x16
queryFlash(0x13) returns 0x00000001
verify flash size...
btflash_init: mfrid=00890089
  devid=00170017
walking flash descriptors (2x16)
btflash_init: found flash 28F640J3A
  flashDescriptor=00035498
  flashSectors=00035394
  nsectors=00000040
  flash_size=01000000
  flash_address_mask=00FFFFFF
no control function
Machine type--> iPAQ 3600
mach_type ->00000016
allocated partition_table
defining partition: bootldr
defining partition: root
initialize_by_mach_type done
probing ram
SDRAM size: 0x02000000
in megs: 32M
Disabling LCD controller
Disabling LCD controller
Enabling LCD controller
before EN
after EN
after EGPIO
DBAR1=C1E436C0
LCCR0=000000B9
LCCR1=0B100930
LCCR2=0A0108F0
LCCR3=00300010
params=0x000359F8
>> Compaq OHH BootLoader, Rev 2-19-58 [BIG_KERNEL] [MD5] [MONO]
>> 03-02-19_17:57
>> Last link date: Wed Feb 19 17:58:00 EST 2003
>> Contact: bootldr@handhelds.org

Cpu company: INTEL
Cpu Architecture: StrongArm
Cpu Part: SA1110
processor ID: 6901B118
>> (c) 2000-2001 Compaq Computer Corporation, provided with NO WARRANTY
under th
e terms of the GNU General Public License.
>> See http://www.handhelds.org/bootldr/ for full license and
sourcesPress Retur
n to start the OS now, any other key for monitor menu
DEBUG BOOT: not evaluating params
DEBUG BOOT: use `params eval' to evaluate parameters.
boot> auxm rx status: 0x00000020
Auxm checksum error, csum: 0x000000A8
msg byte: 0x00000002
msg byte: 0x00000021
msg byte: 0x00000087
msg byte: 0x00000002
boot vfat
h3600_sleeve_init_module
h3600_generic_pcmcia_init_module: registering sleeve drivers
registering sleeve driver 00039D64
registering sleeve driver 00039DB4
registering sleeve driver 00039D14
h3600_sleeve_insert: no spi read, defaulting sleeve vendor
h3600_sleeve_insert: no spi read, defaulting sleeve deviceid
sleeve vendorid=00001125
sleeve deviceid=0000D7C3
pcmcia_probe_sleeve
  probing for dual pcmcia sleeve
  dual_pcmcia_linkup[0]->prc=00001FF0
dual_pcmcia_probe_sleeve
pcmcia_register_ops: ops=00039CE4
h3600_sleeve_insert: matched driver Compaq PC Card Sleeve
pcmcia_init_module
cis mapping=28000000
cis[0] =00000002
  00 28 00 00 FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  00 FF 00 00 00 00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
00 FF 00 00 00 00 00 00 00 00 FF 00 00 00 00 00 00 00 00 FF 00 00 FF 00
00 00 0
0 00 FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
00 00 00 00 00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 01
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 0
0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF 00 00
00 00 00
00 00 00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00 00 00 76 00 00 00
00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF 00 00 00 00 00 00 00 00
00 00 0
0 FF 00 00 00 00 00 00 00 00 00 00 00 FF 00 00 FF 00
cis mapping=38000000
cis[0] =00000001
  01 03 DC 01 FF
  1C 04 03 DC 01 FF
  18 02 DF 01
  20 04 98 00 00 00
  manfid[0]=00000098
  manfid[1]=00000000
  15 15 04 01 54 4F 53 48 49 42 41 00 4D 4B 35 30 30 32 4D 50 4C 00 FF
  21 02 04 01
  funcid=00000004
    fixed disk
  22 02 01 01
  22 03 02 08 1F
  1A 05 01 07 00 02 0F
  1B 0B C0 C0 A1 71 55 46 56 65 08 00 20
  1B 06 00 01 21 B5 1E 56
  1B 0D C1 41 99 71 55 46 56 65 64 F0 FF FF 20
  1B 06 01 01 21 B5 1E 56
  1B 12 C2 41 99 71 55 46 56 65 EA 61 F0 01 07 F6 03 01 EE 20
  1B 06 02 01 21 B5 1E 56
  1B 12 C3 41 99 71 55 46 56 65 EA 61 70 01 07 76 03 01 EE 20
  1B 06 03 01 21 B5 1E 56
end
  serial_number: 82A24695 T
  firmware_revision: V2.10 A
  model_number: TOSHIBA MK5002MPL
  n_sectors_user_addressable=00000000
  bytes_per_sector=00000200
  major_version=00000000
  minor_version=00000000
  flags=0000045A
  ACTUAL bytes_per_sector=00000200
ptable signature=0000AA55
Mounting vfat on partition 00000000
cmd vfat mount: partid=00000000
vfat mount: reading bpb_info
  oemname=mkdosfs
Reading params from file: /boot/params
vfat_find_file_entry: fname='boot/params'
                    dirname='boot'
                   basename='PARAMS'
vfat_find_dir_entry: fname='boot'
                   dirname=''
                  basename='boot'
  searching root_dir_entries
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000002
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000000
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=00000003
   n_bytes=005F021A
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=000000C3
   n_bytes=000B3DFC
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=000000C2
   n_bytes=00000094
+ set linuxargs "init=/linuxrc root=/dev/rd/0 ramdisk_blocksize=4096
console=tty
SA0"
  setting param <linuxargs> to value <init=/linuxrc root=/dev/rd/0
ramdisk_block
size=4096 console=ttySA0>
+ set kernel_filename boot/zimage
  setting param <kernel_filename> to value <boot/zimage>
+ set initrd_filename boot/initrd
  setting param <initrd_filename> to value <boot/initrd>
Reading kernel from file: boot/zimage
vfat_find_file_entry: fname='boot/zimage'
                    dirname='boot'
                   basename='ZIMAGE'
vfat_find_dir_entry: fname='boot'
                   dirname=''
                  basename='boot'
  searching root_dir_entries
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000002
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000000
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=00000003
   n_bytes=005F021A
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=000000C3
   n_bytes=000B3DFC
Reading initrd from file: boot/initrd
vfat_find_file_entry: fname='boot/initrd'
                    dirname='boot'
                   basename='INITRD'
vfat_find_dir_entry: fname='boot'
                   dirname=''
                  basename='boot'
  searching root_dir_entries
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000002
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000000
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=00000003
   n_bytes=005F021A
vfat_find_file_entry: fname='boot/initrd'
                    dirname='boot'
                   basename='INITRD'
vfat_find_dir_entry: fname='boot'
                   dirname=''
                  basename='boot'
  searching root_dir_entries
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000002
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000010
   first_cluster=00000000
   n_bytes=00000000
find_file_in_dir: PARAMS
   attr=00000020
   first_cluster=00000003
   n_bytes=005F021A
C0800000: 1F 8B 08 08 EF 0B AA 3D-00 03 69 6E 69 74 72 64 |
.......=..initrd
C0800010: 2E 63 72 61 6D 66 73 00-6C 5C 05 5C 94 CD F3 3F |
.cramfs.l\.\...?
C0800020: 38 01 69 11 25 A4 44 04-54 1A A4 4B 40 44 45 40 |
8.i.%.D.T..K@DE@
C0800030: BA 9B A3 39 0E 8E EE 0E-29 51 29 29 01 15 14 24 |
...9....)Q))...$
cmd vfat mount: partid=00000000
vfat mount: reading bpb_info
  oemname=mkdosfs
pcmcia_remove_sleeve
Booting vfat...
kernel partition base C0008000
kernel_magic=E1A00000
kernel_region_words[9]=016F2818
Linux ELF flash_imgstart=C0008000 size=00000000 dest=C0000000
offset=00008000
MMU Control=C19F4071
MMU PIDVAM=00000000
Skipping kernel copy by request.
C0008000: E1A00000
C0008004: E1A00000
C0008008: E1A00000
C000800C: E1A00000
C0008010: E1A00000
C0008014: E1A00000
C0008018: E1A00000
C000801C: E1A00000
C0008020: EA000002
C0008024: 016F2818
root_filesystem_name=ide
Grabbed linuxargs, argc = 00000000
Using mach_type 00000016
setting boot parameters to
init=/linuxrc root=/dev/rd/0 ramdisk_blocksize=4096 console=ttySA0
mdcnfg=0000F367
Making core tag at C0000100
Making cmdline tag at C0000114
Making mem32 tag at C00001BC
Making initrd tag at C00001CC
  initrd.start=C0800000
  initrd.size=005F021A
command line is:
mtdparts=ipaq:0x00040000@0x00000000(bootldr)ro,0x00FC0000@0x000
40000(root) init=/linuxrc root=/dev/rd/0 ramdisk_blocksize=4096
console=ttySA0
rootfstype=jffs2
Disabling LCD controller
linuxEntryPoint=C0008000
Booting Linux image
CP15 r0=6901B118
CP15 r1=C19F4071
CP15 r2=C19F4071
CP15 r3=FFFFFFFF
CP15 r5=C19F4011
CP15 r6=C03FEDED
CP15 r13=00000000
CP15 r14=C027DEE0
Uncompressing
Linux...................................................... done,
booting the kernel.
Linux version 2.4.18-rmk3 (cmsj@tenshu) (gcc version 2.95.2 20000313
(Debian GNU
/Linux)) #3 Wed Jul 24 11:36:04 BST 2002
Processor: Intel StrongARM-1110 revision 8
Machine: Compaq iPAQ H3600
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
mtdparts=ipaq:0x00040000@0x00000000(bootldr)ro,0x00FC0000@0
x00040000(root) init=/linuxrc root=/dev/rd/0 ramdisk_blocksize=4096
console=ttyS
A0 rootfstype=jffs2
Console: colour dummy device 80x30
Calibrating delay loop... 137.21 BogoMIPS
Memory: 32MB = 32MB total
Memory: 24320KB available (1436K code, 302K data, 68K init)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
CPU clock: 206.400 MHz (0.000-206.400 MHz)
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis
Communications AB.
ttySA%d0 at MEM 0x80050000 (irq = 17) is a SA1100
Console: switching to colour frame buffer device 40x30
iPAQ H3600 keyboard driver v1.0.1
pty: 256 Unix98 ptys configured
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 8192K size 4096 blocksize
SA1100 flash: probing 32-bit flash bus
Using static partition definition
Creating 2 MTD partitions on "SA1100 flash":
0x00000000-0x00040000 : "H3XXX boot firmware"
mtd: Giving out device 0 to H3XXX boot firmware
0x00040000-0x01000000 : "H3XXX root jffs2"
mtd: Giving out device 1 to H3XXX root jffs2
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
IPv4 over IPv4 tunneling driver
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 6080K
Kernel panic: VFS: Unable to mount root fs on 01:00
Received on Sat Mar 01 21:46:39 2003

This archive was generated by hypermail 2.1.8 : Tue May 04 2004 - 09:42:41 EDT

Re: setting up ipaq with new install method