Re: Help, Intimate install time loop

I had this problem too, but I stuck a 'sleep 1' after loading the pcmcia
stuff and it seems to solve it.

Dino - catch23

James Conner wrote:
>
> Hmm...
>
> OK.. the linuxrc.intimate that I posted only seems to work 100% for me after
> I push the reset button... Just typing 'reboot' doesn't work for me..
>
> I suspect that the sleeve module should be loaded after pcmcia_core or
> something like that... seems to need a delay adding somewhere.
>
> Jim
>
> -----Original Message-----
> From: intimate-admin@handhelds.org
> [mailto:intimate-admin@handhelds.org]On Behalf Of David
> Sent: 08 October 2001 07:36
> To: intimate@handhelds.org
> Subject: [Intimate] Help, Intimate install time loop
>
> Hello,
>
> I've re-installed intimate more times than i can count ,for some
> reason every time after reboot it boots into familiar .. Can someone
> please help me out with this ?
> i've been working on this on and off for a long time at my increasing
> frustration ..
>
> Is some special trick needed to get a dual expansion pack to work ?
>
> I included some info:
>
> Much thanks,
>
> d.
>
> config:
>
> ipaq h3670
> ibm microdrive 512 mb
> prism2 802.11
>
> boot output:
>
> boot
>
> booting jffs2...
> booting boot/zImage from partition >root<
> Disabling LCD controller
>
> Scanning all of flash for your JFFS2 convenience. Est Time: 6-12
> seconds!
> build_list: max = 00F7FFBC
> ..................
> splash: uncompress failed, rc: 0xFFFFFFFB
> dir entries = 00000362
> frag entries = 00000D4F
> +4 increments = 0002AB95
> +file_offset increments = 000010BA
> loaded file of size = 0x000901DC at location 0xC0008000
> kernel_magic=E1A00000
> kernel_region_words[9]=016F2818
> Linux ELF flash_imgstart=50080000 size=00F80000 dest=C0000000
> offset=00008000
> MMU Control=C19F4071
> MMU PIDVAM=00000000
> Skipping kernel copy by request.
>
> C0008000: E1A00000
> C0008004: E1A00000
> C0008008: E1A00000
> C000800C: E1A00000
> C0008010: E1A00000
> C0008014: E1A00000
> C0008018: E1A00000
> C000801C: E1A00000
> C0008020: EA000002
> C0008024: 016F2818
> root_filesystem_name=ramdisk
> Grabbed linuxargs, argc = 00000001
> setting boot parameters to
> noinitrd root=/dev/mtdblock/2 init=/linuxrc.intimate console=ttySA0
> get_param: could not find parameter system_rev
> Makeing core tag at C0000100
> Makeing cmdline tag at C0000114
> Makeing mem32 tag at C0000160
> Makeing ptable tag at C0000170
> dram_size=04000000
> nr_pages=54410001
> command line is: noinitrd root=/dev/mtdblock/2 init=/linuxrc.intimate
> console=ttySA0
> linuxEntryPoint=C0008000
> Booting Linux image
> pre jump mem dump
> C0000100: 05 00 00 00 01 00 41 54-00 00 00 00 00 10 00 00 |
> ......AT........
> C0000110: FF 00 00 00 13 00 00 00-09 00 41 54 6E 6F 69 6E |
> ..........ATnoin
> C0000120: 69 74 72 64 20 72 6F 6F-74 3D 2F 64 65 76 2F 6D | itrd
> root=/dev/m
> C0000130: 74 64 62 6C 6F 63 6B 2F-32 20 69 6E 69 74 3D 2F | tdblock/2
> init=/
> C0000140: 6C 69 6E 75 78 72 63 2E-69 6E 74 69 6D 61 74 65 |
> linuxrc.intimate
> C0000150: 20 63 6F 6E 73 6F 6C 65-3D 74 74 79 53 41 30 00 |
> console=ttySA0.
> C0000160: 04 00 00 00 02 00 41 54-00 00 00 04 00 00 00 C0 |
> ......AT........
> C0000170: 25 00 00 00 0A 00 41 54-70 74 6C 64 03 00 00 00 |
> %.....ATptld....
> C0000180: 62 6F 6F 74 6C 64 72 00-00 00 00 00 00 00 00 00 |
> bootldr.........
> C0000190: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
> ................
> C00001A0: 00 00 00 00 00 00 04 00-02 00 00 00 70 61 72 61 |
> ............para
> C00001B0: 6D 73 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
> ms..............
> C00001C0: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 04 00 |
> ................
> C00001D0: 00 00 04 00 00 00 00 00-72 6F 6F 74 00 00 00 00 |
> ........root....
> C00001E0: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
> ................
> C00001F0: 00 00 00 00 00 00 00 00-00 00 08 00 00 00 F8 00 |
> ................
> C0000200: 18 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
> ................
> C0000210: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
> ................
> C0000220: 00 00 00 00 00 00 00 00-00 00 00 00 | ............
> Uncompressing Linux............................................ done,
> booting the kernel.
>
> Linux version 2.4.7-rmk3-np1-devfs (jamey@rockhopper.crl.dec.com) (gcc
> version 2.95.2 19991024 (release)) #6 Fri Sep 21 17:06:13 EDT 2001
>
> Processor: Intel StrongARM-1110 revision 8
>
> Architecture: Compaq iPAQ
>
> On node 0 totalpages: 16384
>
> zone(0): 16384 pages.
>
> zone(1): 0 pages.
>
> zone(2): 0 pages.
>
> Kernel command line: noinitrd root=/dev/mtdblock/2
> init=/linuxrc.intimate console=ttySA0
>
> Console: colour dummy device 80x30
>
> Calibrating delay loop... 137.21 BogoMIPS
>
> Memory: 64MB = 64MB total
>
> Memory: 62924KB available (1149K code, 262K data, 60K init)
>
> Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
>
> Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
>
> Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
>
> Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
>
> Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
>
> POSIX conformance testing by UNIFIX
>
> Linux NET4.0 for Linux 2.4
>
> Based upon Swansea University Computer Society NET3.039
>
> Initializing RT netlink socket
>
> CPU clock: 206.400 MHz (max 206.400 MHz)
>
> Starting kswapd v1.8
>
> devfs: v0.107 (20010709) Richard Gooch (rgooch@atnf.csiro.au)
>
> devfs: boot_options: 0x2
>
> JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis
> Communications AB.
>
> dma period = 1398056 ps
>
> dma period = 1398056 ps
>
> Console: switching to colour frame buffer device 40x30
>
> sa1100fb_setup_gpio 'mask' for GPIO is 3fc
>
> pty: 256 Unix98 ptys configured
>
> block: queued sectors max/low 41573kB/13857kB, 128 slots per queue
>
> SA1100 flash: probing 32-bit flash bus
>
> SA1100 flash: Found 2 x16 devices at 0x0 in 32-bit mode
>
> parse_bootldr_partitions: magic=0x646c7470
>
> parse_bootldr_partitions: numPartitions=0x3
>
> parse_bootldr_partitions: npartitions=0x3
>
> partition bootldr o=0 s=40000
>
> partition params o=40000 s=40000
>
> partition root o=80000 s=f80000
>
> Using Compaq bootldr partition definition
>
> Creating 3 MTD partitions on "SA1100 flash":
>
> 0x00000000-0x00040000 : "bootldr"
>
> mtd: Giving out device 0 to bootldr
>
> 0x00040000-0x00080000 : "params"
>
> mtd: Giving out device 1 to params
>
> 0x00080000-0x01000000 : "root"
>
> mtd: Giving out device 2 to root
>
> NET4: Linux TCP/IP 1.0 for NET4.0
>
> IP Protocols: ICMP, UDP, TCP, IGMP
>
> IP: routing cache hash table of 512 buckets, 4Kbytes
>
> TCP: Hash tables configured (established 4096 bind 4096)
>
> IPv4 over IPv4 tunneling driver
>
> sa1100fb_setup_gpio 'mask' for GPIO is 3fc
>
> GRE over IPv4 tunneling driver
>
> Linux IP multicast router 0.06 plus PIM-SM
>
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
>
> Fast Floating Point Emulator V0.0 (c) Peter Teichmann.
>
> NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
>
> mtdblock_open
>
> ok
>
> VFS: Mounted root (jffs2 filesystem).
>
> Mounted devfs on /dev
>
> Freeing init memory: 60K
>
> Mounting /proc
> Linux Kernel Card Services 3.1.22
>
> options: [pm]
>
> h3600_init_module:init_module registering char device
>
> initSerialPort: initializing serial port
>
> init_module successful init major= 254 irq=15
>
> h3600_flite_control: pwr=1 brightness=25 ready=0
>
> h3600_init_module registered pm callback=c4873838
>
> init_module successful init major= 0 irq=48
>
> modprobe: Can't locate module h3600_backpaq
> ds: no socket drivers loaded!
>
> /lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o:
> init_module: Operation not permitted
> Hint: insmod errors can be caused by incorrect module parameters,
> including invalid IO or IRQ parameters
> h3600_sleeve_insert: vendorid=0x1125 devid=0x1
>
> h3600_sleeve_insert: unrecognized sleeve
>
> /lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o: insmod
> /lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o failed
> /lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o: insmod ds
> failed
> cardmgr[26]: starting, version is 3.1.20
>
> cardmgr[26]: no pcmcia driver in /proc/devices
>
> cardmgr[26]: exiting
>
> Searching for intimate distribution over ethernet...
> mount: can't find /mnt/nfs in /etc/fstab or /etc/mtab
> unloading Kernel Card Services
>
> Loading floating point emulator...
> insmod: nwfpe: no module by that name found
> Loading Unix socket support
> insmod: unix: no module by that name found
> Setting up RAMFS, please wait...
> Setting Date/Time from previous settings
> Mon Jan 1 00:00:00 UTC 2001
> Executing /sbin/init...
>
> INIT: version 2.78 booting
>
> Mounting local filesystems...
> mount: ramfs already mounted on /mnt/ramfs
> devpts on /dev/pts type devpts (rw,mode=0622)
> mount: proc already mounted
> Calculating module dependencies... done.
> Loading modules: apm apm: BIOS version 1.2 Flags 0x02 (Driver version
> 1.13)
>
> h3600_ts sa1100-rtc SA1100 Real Time Clock driver v1.00
>
> h3600-sleeve h3600_generic_sleeve Linux Kernel Card Services 3.1.22
>
> options: [pm]
>
> SA-1100 PCMCIA (CS release 3.1.22)
>
> sa1100_bitsy_common_pcmcia_get_irq_info
>
> sa1100_bitsy_common_pcmcia_get_irq_info
>
> sa1100: initialization complete
>
> h3600_generic_pcmcia_init_module: registering sleeve drivers
>
> dual_pcmcia_probe_sleeve: Compaq Dual PC Card Sleeve
>
> ****sa1100_bitsy_pcmcia_change_sleeves changed
>
> run_sbin_hotplug:75 * hotplug_path=/sbin/hotplug
>
> h3600_sleeve_register_driver: registered a driver that matches the
> current sleeve Compaq Dual PC Card Sleeve
>
> bitsy-uda1341 modprobe: Can't locate module bitsy-uda1341
>
> Setting the System Clock using the Hardware Clock as reference...
>
> INIT: Entering runlevel: 2
>
> Configuring network interfaces: done.
> Starting PCMCIA services: modulesinsmod: a module named pcmcia_core
> already exists
> insmod: a module named sa1100_cs already exists
> h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
> reset=0
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
> reset=1
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
> reset=0
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
> reset=0
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
> reset=1
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
> reset=0
>
> cardmgr.
> cardmgr[98]: starting, version is 3.1.20
> cardmgr[98]: watching 2 sockets
> cardmgr[98]: Card Services release does not match
> cardmgr[98]: initializing socket 0
> cardmgr[98]: socket 0: Compaq WL110 PC Card
> cardmgr[98]: executing: 'modprobe wvlan_cs'
> wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
>
> wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de>
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
>
> h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
>
> wvlan_cs: index 0x01: Vcc 5.0, irq 42, io 0xf6000000-0xf600003f
>
> wvlan_cs: Registered netdevice eth0
>
> wvlan_cs: MAC address on eth0 is 00 02 2d 00 c5 ec
>
> cardmgr[98]: executing: './network start eth0'
>
> familiar login:
>
> _______________________________________________
> Intimate mailing list
> Intimate@handhelds.org
> http://handhelds.org/mailman/listinfo/intimate
>
> _______________________________________________
> Intimate mailing list
> Intimate@handhelds.org
> http://handhelds.org/mailman/listinfo/intimate
Received on Mon Oct 8 23:39:35 2001