Hello,
I've re-installed intimate more times than i can count ,for some
reason every time after reboot it boots into familiar .. Can someone
please help me out with this ?
i've been working on this on and off for a long time at my increasing
frustration ..
Is some special trick needed to get a dual expansion pack to work ?
I included some info:
Much thanks,
d.
config:
ipaq h3670
ibm microdrive 512 mb
prism2 802.11
boot output:
boot
booting jffs2...
booting boot/zImage from partition >root<
Disabling LCD controller
Scanning all of flash for your JFFS2 convenience. Est Time: 6-12
seconds!
build_list: max = 00F7FFBC
..................
splash: uncompress failed, rc: 0xFFFFFFFB
dir entries = 00000362
frag entries = 00000D4F
+4 increments = 0002AB95
+file_offset increments = 000010BA
loaded file of size = 0x000901DC at location 0xC0008000
kernel_magic=E1A00000
kernel_region_words[9]=016F2818
Linux ELF flash_imgstart=50080000 size=00F80000 dest=C0000000
offset=00008000
MMU Control=C19F4071
MMU PIDVAM=00000000
Skipping kernel copy by request.
C0008000: E1A00000
C0008004: E1A00000
C0008008: E1A00000
C000800C: E1A00000
C0008010: E1A00000
C0008014: E1A00000
C0008018: E1A00000
C000801C: E1A00000
C0008020: EA000002
C0008024: 016F2818
root_filesystem_name=ramdisk
Grabbed linuxargs, argc = 00000001
setting boot parameters to
noinitrd root=/dev/mtdblock/2 init=/linuxrc.intimate console=ttySA0
get_param: could not find parameter system_rev
Makeing core tag at C0000100
Makeing cmdline tag at C0000114
Makeing mem32 tag at C0000160
Makeing ptable tag at C0000170
dram_size=04000000
nr_pages=54410001
command line is: noinitrd root=/dev/mtdblock/2 init=/linuxrc.intimate
console=ttySA0
linuxEntryPoint=C0008000
Booting Linux image
pre jump mem dump
C0000100: 05 00 00 00 01 00 41 54-00 00 00 00 00 10 00 00 |
......AT........
C0000110: FF 00 00 00 13 00 00 00-09 00 41 54 6E 6F 69 6E |
..........ATnoin
C0000120: 69 74 72 64 20 72 6F 6F-74 3D 2F 64 65 76 2F 6D | itrd
root=/dev/m
C0000130: 74 64 62 6C 6F 63 6B 2F-32 20 69 6E 69 74 3D 2F | tdblock/2
init=/
C0000140: 6C 69 6E 75 78 72 63 2E-69 6E 74 69 6D 61 74 65 |
linuxrc.intimate
C0000150: 20 63 6F 6E 73 6F 6C 65-3D 74 74 79 53 41 30 00 |
console=ttySA0.
C0000160: 04 00 00 00 02 00 41 54-00 00 00 04 00 00 00 C0 |
......AT........
C0000170: 25 00 00 00 0A 00 41 54-70 74 6C 64 03 00 00 00 |
%.....ATptld....
C0000180: 62 6F 6F 74 6C 64 72 00-00 00 00 00 00 00 00 00 |
bootldr.........
C0000190: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
................
C00001A0: 00 00 00 00 00 00 04 00-02 00 00 00 70 61 72 61 |
............para
C00001B0: 6D 73 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
ms..............
C00001C0: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 04 00 |
................
C00001D0: 00 00 04 00 00 00 00 00-72 6F 6F 74 00 00 00 00 |
........root....
C00001E0: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
................
C00001F0: 00 00 00 00 00 00 00 00-00 00 08 00 00 00 F8 00 |
................
C0000200: 18 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
................
C0000210: 00 00 00 00 00 00 00 00-00 00 00 00 00 00 00 00 |
................
C0000220: 00 00 00 00 00 00 00 00-00 00 00 00 | ............
Uncompressing Linux............................................ done,
booting the kernel.
Linux version 2.4.7-rmk3-np1-devfs (jamey_at_rockhopper.crl.dec.com) (gcc
version 2.95.2 19991024 (release)) #6 Fri Sep 21 17:06:13 EDT 2001
Processor: Intel StrongARM-1110 revision 8
Architecture: Compaq iPAQ
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: noinitrd root=/dev/mtdblock/2
init=/linuxrc.intimate console=ttySA0
Console: colour dummy device 80x30
Calibrating delay loop... 137.21 BogoMIPS
Memory: 64MB = 64MB total
Memory: 62924KB available (1149K code, 262K data, 60K init)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
CPU clock: 206.400 MHz (max 206.400 MHz)
Starting kswapd v1.8
devfs: v0.107 (20010709) Richard Gooch (rgooch_at_atnf.csiro.au)
devfs: boot_options: 0x2
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis
Communications AB.
dma period = 1398056 ps
dma period = 1398056 ps
Console: switching to colour frame buffer device 40x30
sa1100fb_setup_gpio 'mask' for GPIO is 3fc
pty: 256 Unix98 ptys configured
block: queued sectors max/low 41573kB/13857kB, 128 slots per queue
SA1100 flash: probing 32-bit flash bus
SA1100 flash: Found 2 x16 devices at 0x0 in 32-bit mode
parse_bootldr_partitions: magic=0x646c7470
parse_bootldr_partitions: numPartitions=0x3
parse_bootldr_partitions: npartitions=0x3
partition bootldr o=0 s=40000
partition params o=40000 s=40000
partition root o=80000 s=f80000
Using Compaq bootldr partition definition
Creating 3 MTD partitions on "SA1100 flash":
0x00000000-0x00040000 : "bootldr"
mtd: Giving out device 0 to bootldr
0x00040000-0x00080000 : "params"
mtd: Giving out device 1 to params
0x00080000-0x01000000 : "root"
mtd: Giving out device 2 to root
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
IPv4 over IPv4 tunneling driver
sa1100fb_setup_gpio 'mask' for GPIO is 3fc
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Fast Floating Point Emulator V0.0 (c) Peter Teichmann.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
mtdblock_open
ok
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing init memory: 60K
Mounting /proc
Linux Kernel Card Services 3.1.22
options: [pm]
h3600_init_module:init_module registering char device
initSerialPort: initializing serial port
init_module successful init major= 254 irq=15
h3600_flite_control: pwr=1 brightness=25 ready=0
h3600_init_module registered pm callback=c4873838
init_module successful init major= 0 irq=48
modprobe: Can't locate module h3600_backpaq
ds: no socket drivers loaded!
/lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o:
init_module: Operation not permitted
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters
h3600_sleeve_insert: vendorid=0x1125 devid=0x1
h3600_sleeve_insert: unrecognized sleeve
/lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o: insmod
/lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o failed
/lib/modules/2.4.7-rmk3-np1-devfs/kernel/drivers/pcmcia/ds.o: insmod ds
failed
cardmgr[26]: starting, version is 3.1.20
cardmgr[26]: no pcmcia driver in /proc/devices
cardmgr[26]: exiting
Searching for intimate distribution over ethernet...
mount: can't find /mnt/nfs in /etc/fstab or /etc/mtab
unloading Kernel Card Services
Loading floating point emulator...
insmod: nwfpe: no module by that name found
Loading Unix socket support
insmod: unix: no module by that name found
Setting up RAMFS, please wait...
Setting Date/Time from previous settings
Mon Jan 1 00:00:00 UTC 2001
Executing /sbin/init...
INIT: version 2.78 booting
Mounting local filesystems...
mount: ramfs already mounted on /mnt/ramfs
devpts on /dev/pts type devpts (rw,mode=0622)
mount: proc already mounted
Calculating module dependencies... done.
Loading modules: apm apm: BIOS version 1.2 Flags 0x02 (Driver version
1.13)
h3600_ts sa1100-rtc SA1100 Real Time Clock driver v1.00
h3600-sleeve h3600_generic_sleeve Linux Kernel Card Services 3.1.22
options: [pm]
SA-1100 PCMCIA (CS release 3.1.22)
sa1100_bitsy_common_pcmcia_get_irq_info
sa1100_bitsy_common_pcmcia_get_irq_info
sa1100: initialization complete
h3600_generic_pcmcia_init_module: registering sleeve drivers
dual_pcmcia_probe_sleeve: Compaq Dual PC Card Sleeve
****sa1100_bitsy_pcmcia_change_sleeves changed
run_sbin_hotplug:75 * hotplug_path=/sbin/hotplug
h3600_sleeve_register_driver: registered a driver that matches the
current sleeve Compaq Dual PC Card Sleeve
bitsy-uda1341 modprobe: Can't locate module bitsy-uda1341
Setting the System Clock using the Hardware Clock as reference...
INIT: Entering runlevel: 2
Configuring network interfaces: done.
Starting PCMCIA services: modulesinsmod: a module named pcmcia_core
already exists
insmod: a module named sa1100_cs already exists
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=1
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
reset=1
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=33
reset=0
cardmgr.
cardmgr[98]: starting, version is 3.1.20
cardmgr[98]: watching 2 sockets
cardmgr[98]: Card Services release does not match
cardmgr[98]: initializing socket 0
cardmgr[98]: socket 0: Compaq WL110 PC Card
cardmgr[98]: executing: 'modprobe wvlan_cs'
wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
wvlan_cs: (c) Andreas Neuhaus <andy_at_fasta.fh-dortmund.de>
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
wvlan_cs: index 0x01: Vcc 5.0, irq 42, io 0xf6000000-0xf600003f
wvlan_cs: Registered netdevice eth0
wvlan_cs: MAC address on eth0 is 00 02 2d 00 c5 ec
cardmgr[98]: executing: './network start eth0'
familiar login:
Received on Sun Oct 07 2001 - 22:43:21 EDT
This archive was generated by hypermail 2.2.0 : Mon Jul 25 2005 - 17:21:11 EDT