Snd modules crash on startup 2.6.18-hh1

The ipaq rx3715 linux was crashing every second time (almost
consistently to be inconsequential)

I moved the gpe-bootsplash from /etc/rcS.d/S20bootsplash to
/etc/rc5.d/S98bootsplash
and added a redirection from /etc/init.d/modutils where it invokes the
module insertion >> /var/log/messages 2>&1

here is the normal messages from bootup and here messages with the stack
trace..
after that fails the network card also fail and the bootint process stops..

i have removed sound from the /etc/modules to work around the crash. Is
there enough details in this log? The build was from Romans dump on the
website wiki.

I have begun to try and test the sound modules from the familiar cvs
2.6.19-hh10, but havent got them working yet..
is the sound code in that tree anyway? If not where can I find the sound
code to compile into 2.6.19-hh10, is there a seperate branch for rx3000
work or is there a latest stable patch or something?

regards,

Warren.

syslog.info syslogd started: BusyBox v1.00 (2006.07.23-01:43+0000)
user.notice kernel: klogd started: BusyBox v1.00 (2006.07.23-01:43+0000)
user.notice kernel: Linux version 2.6.18-hh1 (morgan_at_morgan) (gcc version 3.4.1) #13 Wed Nov 29 14:14:41 CET 2006
user.warn kernel: CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
user.warn kernel: Machine: HP iPAQ RX3715
user.warn kernel: Memory policy: ECC disabled, Data cache writeback
user.debug kernel: On node 0 totalpages: 16384
user.debug kernel: DMA zone: 16384 pages, LIFO batch:3
user.warn kernel: CPU S3C2440A (id 0x32440001)
user.warn kernel: S3C244X: core 296.345 MHz, memory 98.781 MHz, peripheral 49.390 MHz
user.info kernel: S3C24XX Clocks, (c) 2004 Simtec Electronics
user.warn kernel: CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on
user.warn kernel: CPU0: D VIVT write-back cache
user.warn kernel: CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
user.warn kernel: CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
user.warn kernel: Built 1 zonelists. Total pages: 16384
user.notice kernel: Kernel command line: root=/dev/mmcblk0p6 rootdelay=2
user.warn kernel: irq: clearing pending status 00004000
user.warn kernel: irq: clearing subpending status 00000092
user.warn kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
user.warn kernel: timer tcon=00511909, tcnt a0c6, tcfg 00000203,00001300, usec 00001f19
user.warn kernel: Console: colour dummy device 80x30
user.warn kernel: Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
user.warn kernel: Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
user.info kernel: Memory: 64MB = 64MB total
user.notice kernel: Memory: 62336KB available (1940K code, 483K data, 104K init)
user.debug kernel: Calibrating delay loop... 147.86 BogoMIPS (lpj=369664)
user.warn kernel: Mount-cache hash table entries: 512
user.info kernel: CPU: Testing write buffer coherency: ok
user.debug kernel: PM: Adding info for No Bus:platform
user.warn kernel: S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
user.warn kernel: Registering sysclass
user.warn kernel: DMA channel 0 at c4800000, irq 33
user.warn kernel: DMA channel 1 at c4800040, irq 34
user.warn kernel: DMA channel 2 at c4800080, irq 35
user.warn kernel: DMA channel 3 at c48000c0, irq 36
user.info kernel: NET: Registered protocol family 16
user.warn kernel: S3C2410 Power Management, (c) 2004 Simtec Electronics
user.info kernel: wake enabled for irq 16
user.warn kernel: S3C2440: Initialising architecture
user.debug kernel: PM: Adding info for platform:s3c2440-uart.0
user.debug kernel: PM: Adding info for platform:s3c2440-uart.1
user.debug kernel: PM: Adding info for platform:s3c2440-uart.2
user.debug kernel: PM: Adding info for platform:asic3.0
user.debug kernel: PM: Adding info for platform:s3c2410-ohci
user.debug kernel: PM: Adding info for platform:s3c2410-lcd
user.debug kernel: PM: Adding info for platform:s3c2410-bl
user.debug kernel: PM: Adding info for platform:s3c2410-wdt
user.debug kernel: PM: Adding info for platform:s3c2440-i2c
user.debug kernel: PM: Adding info for platform:s3c2410-rtc
user.debug kernel: PM: Adding info for platform:s3c2410-iis
user.debug kernel: PM: Adding info for platform:rx3715-sound.0
user.debug kernel: PM: Adding info for platform:rx3715-audio-codec.
user.debug kernel: PM: Adding info for platform:s3c2440-nand
user.debug kernel: PM: Adding info for platform:s3c2440-usbgadget
user.debug kernel: PM: Adding info for platform:s3c2410-ts
user.debug kernel: PM: Adding info for platform:gpio-keys.0
user.debug kernel: PM: Adding info for platform:asic3_keys.0
user.debug kernel: PM: Adding info for platform:rx3715-bt
user.debug kernel: PM: Adding info for platform:rx3715-battery
user.warn kernel: S3C2440: IRQ Support
user.warn kernel: S3C2440: Clock Support, DVS off
user.warn kernel: 0: xdreq0, channels 0---
user.warn kernel: 1: xdreq1, channels -1--
user.warn kernel: 2: sdi, channels 0123
user.warn kernel: 3: spi0, channels -1--
user.warn kernel: 4: spi1, channels ---3
user.warn kernel: 5: uart0, channels 0---
user.warn kernel: 6: uart1, channels -1--
user.warn kernel: 7: uart2, channels ---3
user.warn kernel: 8: timer, channels 0-23
user.warn kernel: 9: i2s-sdi, channels -12-
user.warn kernel: 10: i2s-sdo, channels 0-2-
user.warn kernel: 11: pcm-in, channels 0-2-
user.warn kernel: 12: pcm-out, channels -1-3
user.warn kernel: 13: mic-in, channels --23
user.warn kernel: 14: usb-ep1, channels 0---
user.warn kernel: 15: usb-ep2, channels -1--
user.warn kernel: 16: usb-ep3, channels --2-
user.warn kernel: 17: usb-ep4, channels ---3
user.warn kernel: asic3: using irq 85-154 on irq 56
user.debug kernel: PM: Adding info for platform:asic3_mmc.1283
user.info kernel: NET: Registered protocol family 23
user.info kernel: Bluetooth: Core ver 2.10
user.debug kernel: PM: Adding info for platform:bluetooth
user.info kernel: NET: Registered protocol family 31
user.info kernel: Bluetooth: HCI device and connection manager initialized
user.info kernel: Bluetooth: HCI socket layer initialized
user.info kernel: NET: Registered protocol family 2
user.warn kernel: IP route cache hash table entries: 512 (order: -1, 2048 bytes)
user.warn kernel: TCP established hash table entries: 2048 (order: 1, 8192 bytes)
user.warn kernel: ntries: 1024 (order: 0, 4096 bytes)
user.info kernel: TCP: Hash tables configured (established 2048 bind 1024)
user.info kernel: TCP reno registered
user.warn kernel: NetWinder Floating Point Emulator V0.97 (double precision)
user.info kernel: Initializing Cryptographic API
user.info kernel: io scheduler noop registered
user.info kernel: io scheduler anticipatory registered (default)
user.info kernel: io scheduler deadline registered
user.info kernel: io scheduler cfq registered
user.err kernel: s3c2410 Backlight Driver Initialized.
user.warn kernel: Console: switching to colour frame buffer device 60x53
user.info kernel: fb0: s3c2410fb frame buffer device
user.info kernel: S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
user.info kernel: s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
user.info kernel: s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
user.info kernel: s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
user.info kernel: loop: loaded (max 8 devices)
user.info kernel: PPP generic driver version 2.4.2
user.info kernel: PPP Deflate Compression module registered
user.info kernel: PPP BSD Compression module registered
user.warn kernel: S3C24XX NAND Driver, (c) 2004 Simtec Electronics
user.info kernel: s3c2440-nand s3c2440-nand: Tacls=3, 30ns Twrph0=5 50ns, Twrph1=2 20ns
user.info kernel: NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
user.info kernel: Scanning device for bad blocks
user.notice kernel: Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
user.notice kernel: 0x00000000-0x04000000 : "Whole Flash"
user.warn kernel: Detected S3C2440 - increasing FIFO to 128 bytes
user.debug kernel: udc: pullup(2)
user.debug kernel: PM: Adding info for No Bus:gadget
user.warn kernel: ether gadget: using random self ethernet address
user.warn kernel: ether gadget: using random host ethernet address
user.info kernel: usb0: Ethernet Gadget, version: May Day 2005
user.info kernel: usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk
user.info kernel: usb0: MAC d2:88:4d:58:a8:1c
user.info kernel: usb0: HOST MAC 2a:57:c1:63:d2:a8
user.info kernel: usb0: RNDIS ready
user.debug kernel: udc: pullup(1)
user.info kernel: mice: PS/2 mouse device common for all mice
user.info kernel: ts: Compaq touchscreen protocol output
user.info kernel: input: gpio-keys as /class/input/input0
user.info kernel: input: asic3_keys as /class/input/input1
user.info kernel: s3c2410 TouchScreen successfully loaded
user.info kernel: input: s3c2410 TouchScreen as /class/input/input2
user.warn kernel: S3C24XX RTC, (c) 2004,2006 Simtec Electronics
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: sysfs
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: proc
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: dev (254:0)
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
user.info kernel: i2c /dev entries driver
user.info kernel: Bluetooth: HCI UART driver ver 2.2
user.info kernel: Bluetooth: HCI H4 protocol initialized
user.info kernel: oprofile: using timer interrupt.
user.warn kernel: ip_conntrack version 2.4 (512 buckets, 4096 max) - 180 bytes per conntrack
user.info kernel: TCP bic registered
user.info kernel: NET: Registered protocol family 1
user.info kernel: NET: Registered protocol family 17
user.info kernel: s3c2410-rtc s3c2410-rtc: setting the system clock to 2036-01-01 00:01:17 (2082758477)
user.warn kernel: asic3_mmc: ASIC3 MMC/SD Driver, controller at 0x10000000
user.info kernel: usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet
user.err kernel: ep_disable: ep3-bulk
user.debug kernel: PM: Adding info for mmc:mmc0:b368
user.info kernel: mmcblk0: mmc0:b368 E1213 501248KiB
user.info kernel: mmcblk0: p1 < p5 p6 >
user.info kernel: Waiting 2sec before mounting root device...
user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
user.warn kernel: VFS: Mounted root (ext2 filesystem).
user.info kernel: Freeing init memory: 104K
Starting the hotplug events dispatcher udevd
Synthesizing the initial hotplug events
user.info kernel: iPAQ rx3715 Leds Driver
user.debug kernel: PM: Adding info for platform:asic3-leds.0
user.info kernel: Registered led device: rx3715:green
user.info kernel: Registered led device: rx3715:red
user.info kernel: Registered led device: rx3715:blue
user.info kernel: iPAQ rx3715 Bluetooth Driver
Waiting for /dev to be fully populated
user.info kernel: Bluetooth: L2CAP ver 2.8
user.info kernel: Bluetooth: L2CAP socket layer initialized
user.info kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.2
user.info kernel: Bluetooth: HIDP (Human Interface Emulation) ver 1.1
user.info kernel: IrCOMM protocol (Dag Brattli)
FATAL: Module ohci_hcd not found.
user.info kernel: Bluetooth: RFCOMM socket layer initialized
user.info kernel: Bluetooth: RFCOMM TTY layer initialized
user.info kernel: Bluetooth: RFCOMM ver 1.8
user.info kernel: Bluetooth: SCO (Voice Link) ver 0.5
user.info kernel: Bluetooth: SCO socket layer initialized
user.info kernel: s3c2440-i2c s3c2440-i2c: slave address 0x10
user.info kernel: s3c2440-i2c s3c2440-i2c: bus frequency set to 385 KHz
user.debug kernel: PM: Adding info for No Bus:i2c-0
user.info kernel: s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
user.info kernel: rx3715-sound rx3715-sound.0: probe called
user.warn kernel: mapped channel 10 to 0
user.warn kernel: Initial dcon is 80000000
user.warn kernel: New dcon is 85000000
user.warn kernel: mapped channel 9 to 1
user.warn kernel: Initial dcon is 80000000
user.warn kernel: New dcon is 82000000
user.info kernel: rx3715-sound rx3715-sound.0: soundcard attached ok (c3a399e4)
user.debug kernel: PM: Adding info for i2c:0-001a
user.debug kernel: PM: Removing info for i2c:0-001a
FATAL: Module usbcore not found.
user.warn kernel: acx: this driver is still EXPERIMENTAL
user.warn kernel: acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
user.warn kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
user.warn kernel: running on a little-endian CPU
user.warn kernel: PCI module v0.3.35 initialized, waiting for cards to probe...
user.warn kernel: rx3715_wlan_init: acx-mem platform_device_register
user.debug kernel: PM: Adding info for platform:acx-mem.0
user.warn kernel: rx3715_wlan_start
user.warn kernel: acx: found ACX100-based wireless network card
user.warn kernel: initial debug setting is 0x000A
user.warn kernel: using IRQ 60
user.warn kernel: ACX radio type 0x0d
user.warn kernel: requesting firmware image 'WLANGEN.BIN'
user.warn kernel: acx_write_fw (main):0
user.warn kernel: acx_validate_fw (main):0
user.warn kernel: requesting firmware image 'RADIO0d.BIN'
user.warn kernel: acx_write_fw (radio): 0
user.warn kernel: acx_validate_fw (radio): 0
user.warn kernel: acx100_s_init_wep: writing WEP options
user.warn kernel: initializing max packet templates
user.warn kernel: NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536
user.warn kernel: CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
user.warn kernel: AntennaID:01 Len:02 Data:1E 00
user.warn kernel: PowerLevelID:0A Len:00 Data:
user.warn kernel: DataRatesID:02 Len:05 Data:02 04 11 22 44
user.warn kernel: DomainID:03 Len:07 Data:30 20 30 31 32 40 41
user.warn kernel: ProductID:04 Len:09 Data:TI ACX100
user.warn kernel: ManufacturerID:05 Len:07 Data:TI Tesý
user.warn kernel: get_mask 0x00004D82, set_mask 0x00000000
user.warn kernel: got sensitivity value 176
user.warn kernel: got antenna value 0x8D
user.warn kernel: got Energy Detect (ED) threshold 112
user.warn kernel: got Channel Clear Assessment (CCA) value 13
user.warn kernel: got regulatory domain 0x30
user.warn kernel: get_mask 0x00000000, set_mask 0x00000000 - after update
user.warn kernel: new ratevector: 82 84 0B 16 2C
user.warn kernel: setting RXconfig to 2010:0FDD
user.warn kernel: acx: form factor 0x03 (Compact Flash), radio type 0x0D (Maxim), EEPROM version 0x05, uploaded firmware 'Rev 1.10.7.0' (0x01030505)
user.warn kernel: creating /proc entry driver/acx_wlan0
user.warn kernel: creating /proc entry driver/acx_wlan0_diag
user.warn kernel: creating /proc entry driver/acx_wlan0_eeprom
user.warn kernel: creating /proc entry driver/acx_wlan0_phy
user.warn kernel: acx v0.3.35: net device wlan0, driver compiled against wireless extensions 20 and Linux 2.6.18-hh1
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... usb0 no wireless extensions.

done.
Turning echo off on /dev/s3c2410_serial0
user.debug kernel: selected clock c02123a4 (fclk) quot 1928, calc 9601
Nothing to be done
user.warn kernel: ucons: 00000000, 00000000, 00008fc5
user.debug kernel: selected clock c02123a4 (fclk) quot 213, calc 9616
user.warn kernel: ucons: 00000000, 00000000, 00008fc5
user.debug kernel: selected clock c02123a4 (fclk) quot 213, calc 9616
user.warn kernel: ucons: 00000000, 00000000, 00008fc5
user.debug kernel: selected clock c02123a4 (fclk) quot 213, calc 9616
user.warn kernel: ucons: 00000000, 00000000, 00008fc5
user.debug kernel: selected clock c02123a4 (fclk) quot 213, calc 9616
user.err kernel: s3c2440-i2c s3c2440-i2c: cannot get bus (error -110)
user.err kernel: s3c2440-i2c s3c2440-i2c: cannot get bus (error -110)
user.err kernel: Trying to free already-free IRQ 63

syslog.info syslogd started: BusyBox v1.00 (2006.07.23-01:43+0000)

user.debug kernel: PM: Adding info for platform:rx3715-audio-codec.
user.debug kernel: PM: Adding info for platform:s3c2440-nand
user.debug kernel: PM: Adding info for platform:s3c2440-usbgadget
user.debug kernel: PM: Adding info for platform:s3c2410-ts
user.debug kernel: PM: Adding info for platform:gpio-keys.0
user.debug kernel: PM: Adding info for platform:asic3_keys.0
user.debug kernel: PM: Adding info for platform:rx3715-bt
user.debug kernel: PM: Adding info for platform:rx3715-battery
user.warn kernel: S3C2440: IRQ Support
user.warn kernel: S3C2440: Clock Support, DVS off
user.warn kernel: 0: xdreq0, channels 0---
user.warn kernel: 1: xdreq1, channels -1--
user.warn kernel: 2: sdi, channels 0123
user.warn kernel: 3: spi0, channels -1--
user.warn kernel: 4: spi1, channels ---3
user.warn kernel: 5: uart0, channels 0---
user.warn kernel: 6: uart1, channels -1--
user.warn kernel: 7: uart2, channels ---3
user.warn kernel: 8: timer, channels 0-23
user.warn kernel: 9: i2s-sdi, channels -12-
user.warn kernel: 10: i2s-sdo, channels 0-2-
user.warn kernel: 11: pcm-in, channels 0-2-
user.warn kernel: 12: pcm-out, channels -1-3
user.warn kernel: 13: mic-in, channels --23
user.warn kernel: 14: usb-ep1, channels 0---
user.warn kernel: 15: usb-ep2, channels -1--
user.warn kernel: 16: usb-ep3, channels --2-
user.warn kernel: 17: usb-ep4, channels ---3
user.warn kernel: asic3: using irq 85-154 on irq 56
user.debug kernel: PM: Adding info for platform:asic3_mmc.1283
user.info kernel: NET: Registered protocol family 23
user.info kernel: Bluetooth: Core ver 2.10
user.debug kernel: PM: Adding info for platform:bluetooth
user.info kernel: NET: Registered protocol family 31
user.info kernel: Bluetooth: HCI device and connection manager initialized
user.info kernel: Bluetooth: HCI socket layer initialized
user.info kernel: NET: Registered protocol family 2
user.warn kernel: IP route cache hash table entries: 512 (order: -1, 2048 bytes)
user.warn kernel: TCP established hash table entries: 2048 (order: 1, 8192 bytes)
user.warn kernel: ntries: 1024 (order: 0, 4096 bytes)
user.info kernel: TCP: Hash tables configured (established 2048 bind 1024)
user.info kernel: TCP reno registered
user.warn kernel: NetWinder Floating Point Emulator V0.97 (double precision)
user.info kernel: Initializing Cryptographic API
user.info kernel: io scheduler noop registered
user.info kernel: io scheduler anticipatory registered (default)
user.info kernel: io scheduler deadline registered
user.info kernel: io scheduler cfq registered
user.err kernel: s3c2410 Backlight Driver Initialized.
user.warn kernel: Console: switching to colour frame buffer device 60x53
user.info kernel: fb0: s3c2410fb frame buffer device
user.info kernel: S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
user.info kernel: s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
user.info kernel: s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
user.info kernel: s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
user.info kernel: loop: loaded (max 8 devices)
user.info kernel: PPP generic driver version 2.4.2
user.info kernel: PPP Deflate Compression module registered
user.info kernel: PPP BSD Compression module registered
user.warn kernel: S3C24XX NAND Driver, (c) 2004 Simtec Electronics
user.info kernel: s3c2440-nand s3c2440-nand: Tacls=3, 30ns Twrph0=5 50ns, Twrph1=2 20ns
user.info kernel: NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
user.info kernel: Scanning device for bad blocks
user.notice kernel: Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
user.notice kernel: 0x00000000-0x04000000 : "Whole Flash"
user.warn kernel: Detected S3C2440 - increasing FIFO to 128 bytes
user.debug kernel: udc: pullup(2)
user.debug kernel: PM: Adding info for No Bus:gadget
user.warn kernel: ether gadget: using random self ethernet address
user.warn kernel: ether gadget: using random host ethernet address
user.info kernel: usb0: Ethernet Gadget, version: May Day 2005
user.info kernel: usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk
user.info kernel: usb0: MAC 66:8b:f5:17:61:23
user.info kernel: usb0: HOST MAC 32:5a:0a:bd:90:eb
user.info kernel: usb0: RNDIS ready
user.debug kernel: udc: pullup(1)
user.info kernel: mice: PS/2 mouse device common for all mice
user.info kernel: ts: Compaq touchscreen protocol output
user.info kernel: input: gpio-keys as /class/input/input0
user.info kernel: input: asic3_keys as /class/input/input1
user.info kernel: s3c2410 TouchScreen successfully loaded
user.info kernel: input: s3c2410 TouchScreen as /class/input/input2
user.warn kernel: S3C24XX RTC, (c) 2004,2006 Simtec Electronics
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: sysfs
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: proc
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc intf: dev (254:0)
user.info kernel: s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
user.info kernel: i2c /dev entries driver
user.info kernel: Bluetooth: HCI UART driver ver 2.2
user.info kernel: Bluetooth: HCI H4 protocol initialized
user.info kernel: oprofile: using timer interrupt.
user.warn kernel: ip_conntrack version 2.4 (512 buckets, 4096 max) - 180 bytes per conntrack
user.info kernel: TCP bic registered
user.info kernel: NET: Registered protocol family 1
user.info kernel: NET: Registered protocol family 17
user.info kernel: s3c2410-rtc s3c2410-rtc: setting the system clock to 2036-01-01 00:01:12 (2082758472)
user.warn kernel: asic3_mmc: ASIC3 MMC/SD Driver, controller at 0x10000000
user.info kernel: usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet
user.err kernel: ep_disable: ep3-bulk
user.debug kernel: PM: Adding info for mmc:mmc0:b368
user.info kernel: mmcblk0: mmc0:b368 E1213 501248KiB
user.info kernel: mmcblk0: p1 < p5 p6 >
user.info kernel: Waiting 2sec before mounting root device...
user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
user.warn kernel: VFS: Mounted root (ext2 filesystem).
user.info kernel: Freeing init memory: 104K
Starting the hotplug events dispatcher udevd
Synthesizing the initial hotplug events
user.info kernel: iPAQ rx3715 Leds Driver
user.debug kernel: PM: Adding info for platform:asic3-leds.0
user.info kernel: Registered led device: rx3715:green
user.info kernel: Registered led device: rx3715:red
user.info kernel: Registered led device: rx3715:blue
user.info kernel: iPAQ rx3715 Bluetooth Driver
Waiting for /dev to be fully populated
user.info kernel: Bluetooth: L2CAP ver 2.8
user.info kernel: Bluetooth: L2CAP socket layer initialized
user.info kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.2
user.info kernel: Bluetooth: HIDP (Human Interface Emulation) ver 1.1
user.info kernel: IrCOMM protocol (Dag Brattli)
FATAL: Module ohci_hcd not found.
user.info kernel: Bluetooth: RFCOMM socket layer initialized
user.info kernel: Bluetooth: RFCOMM TTY layer initialized
user.info kernel: Bluetooth: RFCOMM ver 1.8
user.info kernel: Bluetooth: SCO (Voice Link) ver 0.5
user.info kernel: Bluetooth: SCO socket layer initialized
user.info kernel: s3c2440-i2c s3c2440-i2c: slave address 0x10
user.info kernel: s3c2440-i2c s3c2440-i2c: bus frequency set to 385 KHz
user.debug kernel: PM: Adding info for No Bus:i2c-0
user.info kernel: s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
user.info kernel: rx3715-sound rx3715-sound.0: probe called
user.warn kernel: mapped channel 10 to 0
user.warn kernel: Initial dcon is 80000000
user.warn kernel: New dcon is 85000000
user.warn kernel: mapped channel 9 to 1
user.warn kernel: Initial dcon is 80000000
user.warn kernel: New dcon is 82000000
user.info kernel: rx3715-sound rx3715-sound.0: soundcard attached ok (c38a89e4)
user.err kernel: s3c2440-i2c s3c2440-i2c: cannot get bus (error -110)
Segmentation fault
user.err kernel: s3c2440-i2c s3c2440-i2c: cannot get bus (error -110)
user.alert kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000008
user.alert kernel: pgd = c3f68000
user.alert kernel: [00000008] *pgd=33688031, *pte=00000000, *ppte=00000000
user.warn kernel: Internal error: Oops: 17 [#1]
user.warn kernel: Modules linked in: i2c_s3c2410 snd_rx3715_audio s3c24xx_iis snd_uda1380 snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore sco rfcomm irnet irlan ircomm_tty ircomm hidp bnep l2cap rx3715_bt rx3715_leds
user.warn kernel: CPU: 0
user.warn kernel: PC is at flush_workqueue+0x10/0x4c
user.warn kernel: LR is at destroy_workqueue+0x14/0xa0
user.warn kernel: pc : [<c004aff8>] lr : [<c004b138>] Not tainted
user.warn kernel: sp : c3517e64 ip : c3517e78 fp : c3517e74
user.warn kernel: r10: bf094d00 r9 : c3516000 r8 : bf094880
user.warn kernel: r7 : 00000000 r6 : c3567620 r5 : bf09352c r4 : 00000000
user.warn kernel: r3 : 00000000 r2 : 00000600 r1 : 00000208 r0 : 00000000
user.warn kernel: Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment user
user.warn kernel: Control: C000717F Table: 33F68000 DAC: 00000015
user.warn kernel: Process modprobe (pid: 3825, stack limit = 0xc3516250)
user.warn kernel: Stack: (0xc3517e64 to 0xc3518000)
user.warn kernel: 7e60: 00000000 c3517e8c c3517e78 c004b138 c004aff8 bf094880 bf09352c
user.warn kernel: 7e80: c3517ea0 c3517e90 bf08a6bc c004b134 bf09351c c3517ec8 c3517ea4 bf0933b0
user.warn kernel: 7ea0: bf08a690 c02120c0 00000000 00000000 bf0947cc c0022f44 00000000 c3517ee8
user.warn kernel: 7ec0: c3517ecc c0119950 bf093254 c0212190 c02120c0 c0119a44 bf0947cc c3517f00
user.warn kernel: 7ee0: c3517eec c0119ac4 c01198d4 00000000 c3517f04 c3517f2c c3517f04 c0118d68
user.warn kernel: 7f00: c0119a54 c0222c24 c0222c24 c0212108 bf0947e0 bf0947cc 00000000 c0222b24
user.warn kernel: 7f20: c3517f3c c3517f30 c0119b44 c0118d28 c3517f64 c3517f40 c0119318 c0119b34
user.warn kernel: 7f40: bf0947cc bf094b80 00000000 00000080 c0022f44 00000000 c3517f78 c3517f68
user.warn kernel: 7f60: c0119fe8 c01192bc 000024bd c3517f88 c3517f7c bf096024 c0119f68 c3517fa4
user.warn kernel: 7f80: c3517f8c c0056dd8 bf096010 0000941c 00000000 00000000 00000000 c3517fa8
user.warn kernel: 7fa0: c0022da0 c0056d28 0000941c 00000000 40019000 000024bd 00016130 00016130
user.warn kernel: 7fc0: 0000941c 00000000 00000000 00000000 000160e0 000160d0 00000000 000160ec
user.warn kernel: 7fe0: 00015100 bef3cadc 0000a434 400e607c 60000010 40019000 00000000 00000000
user.warn kernel: Backtrace:
user.warn kernel: [<c004afe8>] (flush_workqueue+0x0/0x4c) from [<c004b138>] (destroy_workqueue+0x14/0xa0)
user.warn kernel: r4 = 00000000
user.warn kernel: [<c004b124>] (destroy_workqueue+0x0/0xa0) from [<bf08a6bc>] (snd_uda1380_deactivate+0x3c/0x84 [snd_uda1380])
user.warn kernel: r5 = BF09352C r4 = BF094880
user.warn kernel: [<bf08a680>] (snd_uda1380_deactivate+0x0/0x84 [snd_uda1380]) from [<bf0933b0>] (rx3715_audio_codec_probe+0x16c/0x200 [snd_rx3715_audio])
user.warn kernel: r4 = BF09351C
user.warn kernel: [<bf093244>] (rx3715_audio_codec_probe+0x0/0x200 [snd_rx3715_audio]) from [<c0119950>] (driver_probe_device+0x8c/0xd4)
user.warn kernel: [<c01198c4>] (driver_probe_device+0x0/0xd4) from [<c0119ac4>] (__driver_attach+0x80/0xe0)
user.warn kernel: r7 = BF0947CC r6 = C0119A44 r5 = C02120C0 r4 = C0212190
user.warn kernel: [<c0119a44>] (__driver_attach+0x0/0xe0) from [<c0118d68>] (bus_for_each_dev+0x50/0x84)
user.warn kernel: r5 = C3517F04 r4 = 00000000
user.warn kernel: [<c0118d18>] (bus_for_each_dev+0x0/0x84) from [<c0119b44>] (driver_attach+0x20/0x28)
user.warn kernel: r7 = C0222B24 r6 = 00000000 r5 = BF0947CC r4 = BF0947E0
user.warn kernel: [<c0119b24>] (driver_attach+0x0/0x28) from [<c0119318>] (bus_add_driver+0x6c/0x138)
user.warn kernel: [<c01192ac>] (bus_add_driver+0x0/0x138) from [<c0119fe8>] (driver_register+0x90/0xa0)
user.warn kernel: [<c0119f58>] (driver_register+0x0/0xa0) from [<bf096024>] (rx3715_audio_init+0x24/0x34 [snd_rx3715_audio])
user.warn kernel: r4 = 000024BD
user.warn kernel: [<bf096000>] (rx3715_audio_init+0x0/0x34 [snd_rx3715_audio]) from [<c0056dd8>] (sys_init_module+0xc0/0x1ac)
user.warn kernel: [<c0056d18>] (sys_init_module+0x0/0x1ac) from [<c0022da0>] (ret_fast_syscall+0x0/0x2c)
user.warn kernel: r6 = 00000000 r5 = 00000000 r4 = 0000941C
user.warn kernel: Code: e1a0c00d e92dd810 e24cb004 e1a04000 (e5942008)
FATAL: Module usbcore not found.
user.warn kernel: acx: this driver is still EXPERIMENTAL
user.warn kernel: acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
user.warn kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
user.warn kernel: running on a little-endian CPU
user.warn kernel: PCI module v0.3.35 initialized, waiting for cards to probe...