Re: [jornada] has anyone the sandisk connect plusWIFI successfully working?

it is a CF card. A combination of 128MB storage card and a WI-FI card. I've tried to use with a Jornada568, familiar 0.8.2 and hostap 3.7 - diver & -utils .

It has a prism3 chipset and need the hostap_cs driver.
I've googled and get the information that it works on open-zaurus (see: http://www.bentzon.net/acb/sandisk.html)
but i found nothing for familiar.

When I insert the card I get this messages:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

<7>Probing IDE interface ide0...
<4>hda: SanDisk SDCFB-256, CFA DISK drive
<4>ide0 at 0xc68a0000-0xc68a0007,0xc68a000e on irq 93
<6>ide-cs: hda: Vcc = 3.3, Vpp = 0.0
<6>hda: max request size: 128KiB
<6>hda: 501760 sectors (256 MB) w/1KiB Cache, CHS=980/16/32
<7>hda: cache flushes not supported
<6> /dev/ide/host0/bus0/target0/lun0: p1
<6> /dev/ide/host0/bus0/target0/lun0: p1
<4>Stopping tasks: =================|
<4>hda: lost interrupt
<4>Restarting tasks... done
<4>Stopping tasks: =================|
<4>hda: lost interrupt
<4>Restarting tasks... done
<7>hostap_crypt: registered algorithm 'NULL'
<6>hostap_cs: 0.1.3 - 2004-02-08 (Jouni Malinen )
<7>hostap_cs: setting Vcc=33 (constant)
<7>hostap_cs: CS_EVENT_CARD_INSERTION
<7>hostap_cs: setting Vcc=33 (from config)
<7>Checking CFTABLE_ENTRY 0x01 (default 0x01)
<7>IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
<7>io->flags = 0x0047, io.base=0x0000, len=128
<7>eth%d: Interrupt, but dev not OK
<6>hostap_cs: index 0x01: Vcc 3.3, irq 93, io 0xc68a0000-0xc68a007f
<6>hostap_cs: Registered netdevice wlan0
<4>hostap_cs: card initialization timed out
<7>Probing IDE interface ide0...
<4>hda: SanDisk SDWCFB-128, CFA DISK drive
<7>wlan0: Host AP mode does not support 'Any' essid
<7>prism2: wlan0: operating mode changed 3 -> 2
<7>wlan0: hfa384x_cmd_issue: cmd reg was busy for 1343 usec
<4>ide0 at 0xc68a0000-0xc68a0007,0xc68a000e on irq 93
<6>hda: max request size: 128KiB
<6>hda: 250880 sectors (128 MB) w/1KiB Cache, CHS=980/8/32
<7>hda: cache flushes not supported

<6> /dev/ide/host0/bus0/target0/lun0:<7>wlan0: hfa384x_cmd: entry still in list? (entry=c36037a0, type=0, res=0)

<7>wlan0: hfa384x_cmd: command was not completed (res=0, entry=c36037a0, type=0, cmd=0x0121, param0=0xfc00, EVSTAT=427f INTEN=2020)

<4>wlan0: interrupt delivery does not seem to work

<7>wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=-110, rid=fc00, len=2)

<7>wlan0: hfa384x_cmd: entry still in list? (entry=c2af0de0, type=0, res=0)

<7>wlan0: hfa384x_cmd: command was not completed (res=0, entry=c2af0de0, type=0, cmd=0x0001, param0=0x0000, EVSTAT=427f INTEN=0000)

<4>wlan0: interrupt delivery does not seem to work
<4>wlan0: MAC port 0 enabling failed
<4>wlan0: could not enable MAC port

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

When i try to flash the firmware i get this:

--------------------------------------------------------------------------------
prism2_srec -gs wlan0 pm010101.hex
srec summary for pm010102.hex
Included file name: PM010102.HEX
Component: 0x0015 1.1.2 (primary firmware)

Verifying update compatibility and combining data:
Failed to open '/proc/net/hostap/wlan0/debug' for reading.
Incompatible update data.
--------------------------------------------------------------------------------

hostap_diag brings me this:

--------------------------------------------------------------------------------
Host AP driver diagnostics information for 'wlan0'

Could not communicate with the kernel driver.
--------------------------------------------------------------------------------

Henner

Adam Pribyl <covex_at_ahoj.fsik.cvut.cz> schrieb am 30.09.05 17:25:57:
>
> On Fri, 30 Sep 2005 my-email_at_web.de wrote:
>
> >
> > Hi,
> >
> > I have a sandisk connect plus wifi card. But it doesn't work with familiar 0.8.2.
> >
>
> Whats that? CF? PCMCIA? Is it PC CARD or CARDBUS? How did you connected
> CF? Trought PCMCIA?
>
> > Has anyone these card successfully working?
> >
> > Henner
>
> _______________________________________________
> jornada mailing list
> jornada_at_handhelds.org
> https://handhelds.org/mailman/listinfo/jornada

______________________________________________________________
Verschicken Sie romantische, coole und witzige Bilder per SMS!
Jetzt bei WEB.DE FreeMail: http://f.web.de/?mc=021193
Received on Fri Sep 30 2005 - 12:45:33 EDT