Everyone,
I'm using the 0.5pre root image and the 2.15.15 bootloader. My hardware
congiguration is a dual PCMCIA sleeve, 1 GB microdrive, Lucent Orinoco
Gold 802.11 card, on a Ipaq 3670.
I noticed that as long as someone follows the bootloader instructions
exactly, this card works great! No modifications or module problems,
since I'm trying to consolidate the documentation for Familiar, this was
important to me. It's identified as "WaveLAN/IEEE PCMCIA driver v1.0.6"
At boot-up, the following is displayed:
Starting PCMCIA services: modulesinsmod: a module named pcmcia_core
already exists
h3600_dual_sleeve_pcmcia_configure_socket: socket=1
insmod: a module named sa1100_cs already exists.in_hotplug:75 *
hotplug_path=/sbin/hotplug
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
cardmg
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=1 Invalid argumentus settings: exiting/imlib-base_1.9.11-
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
h3600_dual_
Mon Jan 1 00:00:00 UT
cardmgr[101]: starting, version is 3.1.22
h36
cardmgr[101]: socket 0: Compaq WL
cardmgr[101]: watching 2 socketst=0/
cardmgr[101]: could not adjust resource: IO ports 0xc00-0xcff: Invalid
argumentrdmgr[101]: executing: 'modprobe wvlan_cs' unix: no
cardmgr[101]: could not adjust resource: IO ports 0x800-0x8ff: Invalid
argument
wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
cardmgr[101]: could not adjust resource: IO portsists: watch
Trying to fr
cardmgr[101]: could not adjust resource: irq 4: Invalid argument
cardmgr[101]: executing: 'modprobe wvlan_cs'
wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de>
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0 reset=0
wvlan_cs: index 0x01: Vcc 5.0, irq 42, io 0xf6000000-0xf600003f
wvlan_cs: Registered netdevice eth0
wvlan_cs: MAC address on eth0 is 00 02 2d 2d c9 06
cardmgr[101]: executing: './network start eth0'
And strangely enough, right after logging in as root, another batch of
messages appears:
familiar login: cardmgr[101]: + Operation failed.
cardmgr[101]: socket 1: ATA/IDE Fixed Disk
cardmgr[101]: executing: 'modprobe ide-cs'
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with
idebus=xx
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=0 reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=33 vpp=0 reset=0
Trying to free nonexistent resource <f7000000-f700000f>
hda: IBM-DSCM-11000, ATA DISK drive
ide0 at 0xf7000000-0xf7000007,0xf700000e on irq 32
ide_cs: hda: Vcc = 3.3, Vpp = 0.0
cardmgr[101]: executing: './ide start hda'
hda: bad special flag: 0x03
So the card works, is this final data just a delayed initialization of
the Card Services or the PCMCIA card drivers?
Thanks,
Jason
-----Original Message-----
From: Mika.Laitio@sysline.com [mailto:Mika.Laitio@sysline.com]
Sent: Wednesday, October 10, 2001 6:27 AM
To: Brauel, Bjoern
Cc: ipaq@handhelds.org; ipaq-admin@handhelds.org
Subject: RE: [iPAQ] PROBLEM WITH ORINOCO CARD
I have tried WLAN and Orinocos drivers with 0.5 and single PCMCIA sleeve
without success.
This Orinoco's card worked just fine in Familiar 0.4 (Kernel 2.4.3) and
WLAN-drivers. It however didn't
work with Orinoco's drivers.
Mika
"Brauel, Bjoern"
<Bjoern.Brauel@softw To: "'Munson, Jason
(MED)'" <Jason.Munson@med.ge.com>, ipaq@handhelds.org
areag.com> cc:
Sent by: Subject: RE: [iPAQ]
PROBLEM WITH ORINOCO CARD
ipaq-admin@handhelds
.org
10.10.2001 11:31
Are you using the wvlan or the orinoco driver ?
-----Original Message-----
From: Munson, Jason (MED) [mailto:Jason.Munson@med.ge.com]
Sent: Tuesday, October 09, 2001 7:47 PM
To: ipaq@handhelds.org
Subject: RE: [iPAQ] PROBLEM WITH ORINOCO CARD
I have no problems using the default 0.5 image and a Lucent Orinoco Gold
card. I used the 2.15.15 bootloader and the image specified in the
0.5pre installation document. I also have a dual PCMCIA sleeve, so I'm
not certain about using it with the single sleeve.
Jason
-----Original Message-----
From: Brauel, Bjoern [mailto:Bjoern.Brauel@softwareag.com]
Sent: Tuesday, October 09, 2001 8:34 AM
To: 'Erkki Harjula'; ipaq@handhelds.org
Subject: RE: [iPAQ] PROBLEM WITH ORINOCO CARD
There is still a general problem with that card. You should use the
orinoco
driver
for it, but unfortunately that doesn't work either at the moment.
I may be able to send you the required modules for 2.4.7 so you can
at least get it working.
-----Original Message-----
From: Erkki Harjula [mailto:erkkih@ees2.oulu.fi]
Sent: Tuesday, October 09, 2001 2:44 PM
To: ipaq@handhelds.org
Subject: [iPAQ] PROBLEM WITH ORINOCO CARD
I installed Familiar 0.5 on my iPaq, everything works well, but I can't
get
wlan card work. Card is Orinoco gold. Here's the message that I get when
I
switch the card on to iPaq:
------------------------------------------------------------------------
---
sh-2.03# h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50
vpp=50 reset=0
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=1
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
cardmgr[83]: initializing socket 0
cardmgr[83]: socket 0: Compaq WL110 PC Card
cardmgr[83]: executing: 'modprobe wvlan_cs'
wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de>
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0
reset=0
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0
reset=0
wvlan_cs: index 0x01: Vcc 5.0, irq 42, io 0xf6000000-0xf600003f
wvlan_cs: Registered netdevice eth0
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
cardmgr[83]: executing: './network start eth0'
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
...
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
cardmgr[83]: + Operation failed.
------------------------------------------------------------------------
---
It seems to recognize the card as Compaq WL110 when it should be Lucent
Orinoco Gold. With familiar 0.4 everything worked well on this same
device.
I feel quite frustrated, when I have installed every pcmcia any wlan
modules over and nothing seems to help.
Regards,
Erkki
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
Received on Wed Oct 10 09:08:37 2001
This archive was generated by hypermail 2.1.8 : Tue May 04 2004 - 09:44:13 EDT