[iPAQ] prism2 card (Linksys) failure with pre v0.5

I have been having great difficulty getting this Linksys card to work with
the new familiar pre-release v0.5 or v0.4. I am using a dual sleeve which is
working fine, but the prism2 cards just don't want to work, it seems. After
installing familiar v0.5, I installed
wlan-ng-2.4.7-rmk3-np1-devfs_0.1.9-hh0_arm.ipk from
http://handhelds.org/~sjohnson/feed/. After I plug in the card it prints the
following to the console:

cardmgr[5203]: executing: './wlan-ng stop wlan0'
cardmgr[5203]: + Operation failed.
cardmgr[5203]: executing: 'modprobe -r prism2_cs'
prism2_cs.o: 0.1.9 Unloaded
p80211.o: 0.1.9 Unloaded
cardmgr[5203]: + Note: /etc/modules.conf is more recent than
/lib/modules/2.4.7-rmk3-np1-devfs/modules.dep
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=50 vpp=50 reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=50 vpp=50 reset=1
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=50 vpp=50 reset=0
cardmgr[5203]: initializing socket 1
cardmgr[5203]: socket 1: Linksys WPC11 11Mbps 802.11b WLAN Card
cardmgr[5203]: product info: "Instant Wireless ", " Network PC CARD",
"Version 01.02", ""
cardmgr[5203]: manfid: 0x0156, 0x0002 function: 6 (network)
cardmgr[5203]: executing: 'modprobe prism2_cs'
cardmgr[5203]: + Note: /etc/modules.conf is more recent than
/lib/modules/2.4.7-rmk3-np1-devfs/modules.dep
init_module: prism2_cs.o: 0.1.9 Loaded
init_module: dev_info is: prism2_cs
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=50 vpp=0 reset=0
h3600_dual_sleeve_pcmcia_configure_socket: socket=1 vcc=50 vpp=0 reset=0
prism2_cs: index 0x01: Vcc 5.0, irq 32, io 0xf7000000-0xf700003f
ident: nic h/w: id=0x8002 1.0.0
ident: pri f/w: id=0x15 0.3.0
ident: sta f/w: id=0x1f 0.8.3
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x01:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/2
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/6
PRI-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Prism2 card SN: 99SA01000000
cardmgr[5203]: executing: './wlan-ng start wlan0'
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11WEPDefaultKeyID=0
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11ExcludeUnencrypted=true
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11PrivacyInvoked=true
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11WEPDefaultKey0=xx:xx:xx:xx:xx
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + +: not found
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11WEPDefaultKey0=xx:xx:xx:xx:xx
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + +: not found
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11WEPDefaultKey0=xx:xx:xx:xx:xx
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + +: not found
cardmgr[5203]: + message=dot11req_mibset
cardmgr[5203]: + mibattribute=dot11WEPDefaultKey0=xx:xx:xx:xx:xx
cardmgr[5203]: + resultcode=success
cardmgr[5203]: + +: not found
p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame
dropped.
p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame
dropped.
p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame
dropped.
p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame
dropped.
...
and so on, then fails

Does anyone know what those "not found" errors are above? In my wlan-ng.opts
file, these are the lines I edited (network.opts is set up for dhcp):

dot11PrivacyInvoked=true # true|false
dot11WEPDefaultKeyID=0 # 0|1|2|3
dot11ExcludeUnencrypted=true # true|false, in AP this means WEP
                                        # is required for all STAs
# If PRIV_GENSTR is not empty, use PRIV_GENTSTR to generate
# keys (just a convenience)
PRIV_GENERATOR=/sbin/nwepgen # nwepgen, Neesus compatible
PRIV_KEY128=false # keylength to generate
PRIV_GENSTR="p455w3rd"

AuthType="sharedkey" # opensystem | sharedkey (requires WEP)
DesiredSSID="MySSID"

Using these settings on my laptop seems to work. I have tried 128-bit,
64-bit, and no WEP and all get the same results on the ipaq. I have also
used a single pcmcia sleeve as well as a dual-sleeved pcmcia sleeve with the
same results. Can anyone help me out here?
Received on Tue Oct 9 12:07:11 2001