RE: [iPAQ] PROBLEM WITH ORINOCO CARD

I have no problems using the default 0.5 image and a Lucent Orinoco Gold
card. I used the 2.15.15 bootloader and the image specified in the
0.5pre installation document. I also have a dual PCMCIA sleeve, so I'm
not certain about using it with the single sleeve.

Jason

-----Original Message-----
From: Brauel, Bjoern [mailto:Bjoern.Brauel@softwareag.com]
Sent: Tuesday, October 09, 2001 8:34 AM
To: 'Erkki Harjula'; ipaq@handhelds.org
Subject: RE: [iPAQ] PROBLEM WITH ORINOCO CARD

There is still a general problem with that card. You should use the
orinoco
driver
for it, but unfortunately that doesn't work either at the moment.
I may be able to send you the required modules for 2.4.7 so you can
at least get it working.

-----Original Message-----
From: Erkki Harjula [mailto:erkkih@ees2.oulu.fi]
Sent: Tuesday, October 09, 2001 2:44 PM
To: ipaq@handhelds.org
Subject: [iPAQ] PROBLEM WITH ORINOCO CARD

I installed Familiar 0.5 on my iPaq, everything works well, but I can't
get
wlan card work. Card is Orinoco gold. Here's the message that I get when
I
switch the card on to iPaq:

------------------------------------------------------------------------

---
sh-2.03# h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50
vpp=50 reset=0
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=1
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=50
reset=0
cardmgr[83]: initializing socket 0
cardmgr[83]: socket 0: Compaq WL110 PC Card
cardmgr[83]: executing: 'modprobe wvlan_cs'
wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.6
wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de>
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0
reset=0
h3600_single_sleeve_pcmcia_configure_socket: socket=0 vcc=50 vpp=0
reset=0
wvlan_cs: index 0x01: Vcc 5.0, irq 42, io 0xf6000000-0xf600003f
wvlan_cs: Registered netdevice eth0
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
cardmgr[83]: executing: './network start eth0'
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
	...
NETDEV WATCHDOG: eth0: transmit timed out
wvlan_cs: eth0 Tx timed out! Resetting card
wvlan_cs: MAC address on eth0 is 00 00 00 00 00 00
wvlan_cs: Initialization failed!
cardmgr[83]: + Operation failed.
------------------------------------------------------------------------
---
It seems to recognize the card as Compaq WL110 when it should be Lucent
Orinoco Gold. With familiar 0.4 everything worked well on this same
device.
I feel quite frustrated, when I have installed every pcmcia any wlan
modules over and nothing seems to help.
Regards,
Erkki
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq
_______________________________________________
iPAQ mailing list
iPAQ@handhelds.org
http://handhelds.org/mailman/listinfo/ipaq
irc://irc.openprojects.net #ipaq