[iPAQ] booting problem (long)

I have an iPAQ 3650 and have successfully loaded familiar and opie and
upgraded them both to the latest version. I was running for two days and
then tried to install a new package. Now when I boot, I get the following
message and it won't let me login. I had run into this before and
reflashed the image and got it running for the last two days, now this is
back. What steps should I take next or do I just need to reflash?

<Serial_console_output>
U3
@000003F8
F02000000

*MTST
00000001
00000002
00000004
00000008
00000010
00000020
00000040
00000080
00000100
00000200
00000400
00000800
00001000
00002000
00004000
00008000
00010000
00020000
00040000
00080000
00100000
00200000
00400000
00800000
01000000
02000000
04000000
08000000
10000000
20000000
40000000
80000000
ENDM
STKP
C19F3FF0
verify flash size...
btflash_init: mfrid=00890089
  devid=00170017
walking flash descriptors (2x16)
btflash_init: found flash 28F640J3A
  flashDescriptor=0002C938
  flashSectors=0002C834
  nsectors=00000040
  flash_size=01000000
  flash_address_mask=00FFFFFF
mach_type ->00000016
gpio_init mach_type=00000016
allocated partition_table
defining partition: bootldr
defining partition: root
Probing bank0 memory size...
 bank0 memory size=02000000
SDRAM size: 0x02000000
 in megs: 32M
Disabling LCD controller
Disabling LCD controller
Enabling LCD controller
before EN
after EN
after EGPIO
DBAR1=C1E3A440
LCCR0=000000B9
LCCR1=0B100930
LCCR2=0A0108F0
LCCR3=00300010
params=0x0002CEB4
>> Compaq OHH BootLoader, Rev 2-18-54 [BIG_KERNEL] [MD5] [MONO]
>> 02-10-17_16:29
>> Last link date: Thu Oct 17 16:29:24 EDT 2002
>> Contact: bootldr@handhelds.org

>> StrongARM SA-1110 revision B4
>> (c) 2000-2001 Compaq Computer Corporation, provided with NO WARRANTY
under th
e terms of the GNU General Public License.
>> See http://www.handhelds.org/bootldr/ for full license and sourcesPress
Retur
n to start the OS now, any other key for monitor menu
DEBUG BOOT: not evaluating params
DEBUG BOOT: use `params eval' to evaluate parameters.
boot> boot
booting jffs2...
booting boot/zImage from partition >root<
Scanning all of flash for your JFFS2 convenience. Est Time: 6-12 seconds!
build_list: max = 00FBFFBC
..
dir entries = 000009C7
frag entries = 00001EF6
+4 increments = 00000000
+file_offset increments = 00004552
loaded file of size = 0x00095390 at location 0xC0008000
kernel partition base C0008000
kernel_magic=E1A00000
kernel_region_words[9]=016F2818
Linux ELF flash_imgstart=50040000 size=00FC0000 dest=C0000000 offset=00008000
MMU Control=C19F4071
MMU PIDVAM=00000000
Skipping kernel copy by request.
C0008000: E1A00000
C0008004: E1A00000
C0008008: E1A00000
C000800C: E1A00000
C0008010: E1A00000
C0008014: E1A00000
C0008018: E1A00000
C000801C: E1A00000
C0008020: EA000002
C0008024: 016F2818
root_filesystem_name=ramdisk
Grabbed linuxargs, argc = 00000001
Using mach_type 00000016
setting boot parameters to
 noinitrd root=/dev/mtdblock1 init=/linuxrc console=ttySA0
Makeing core tag at C0000100
Makeing cmdline tag at C0000114
Makeing mem32 tag at C0000198
Makeing ptable tag at C00001A8
dram_size=02000000
command line is:
mtdpart=bootldr@0x00000000:0x00040000,root@0x00040000:0x00FC000
0 noinitrd root=/dev/mtdblock1 init=/linuxrc console=ttySA0
Disabling LCD controller
linuxEntryPoint=C0008000
Booting Linux image
Uncompressing Linux............................................. done,
booting t
he kernel.
Linux version 2.4.18-rmk3 (jamey@vimes.crl.hpl.hp.com) (gcc version 2.95.3
20010
315 (release)) #5 Tue Dec 17 14:47:51 EST 2002
Processor: Intel StrongARM-1110 revision 8
Machine: Compaq iPAQ H3600
Ignoring unrecognised tag 0x5441000a
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
mtdpart=bootldr@0x00000000:0x00040000,root@0x00040000:0x00F
C0000 noinitrd root=/dev/mtdblock1 init=/linuxrc console=ttySA0
Console: colour dummy device 80x30
Calibrating delay loop... 137.21 BogoMIPS
Memory: 32MB = 32MB total
Memory: 30692KB available (1150K code, 299K data, 68K init)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
CPU clock: 206.400 MHz (0.000-206.400 MHz)
sa1110_clk_init: h3xxx_membank_size[0]=33554432
sa1110_clk_init: 100 MHz Samsung 4Mx16bitx4banks SDRAM
SDRAM: tck: 10 trcd: 20 trp: 20 twr: 10 refresh: 64000 cas_latency: 3
Starting kswapd
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications
AB.
ttySA%d0 at MEM 0x80050000 (irq = 17) is a SA1100
Console: switching to colour frame buffer device 40x30
iPAQ H3600 keyboard driver v1.0.1
pty: 256 Unix98 ptys configured
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
IPAQ flash: probing 32-bit flash bus, window=c28c0000
parse_mtdpart{bootldr@0x00000000:0x00040000,root@0x00040000:0x00FC0000}
         name=bootldr
         at_pos=0x00000000
         colon_pos=0x00040000,root@0x00040000:0x00FC0000
         comma_pos=,root@0x00040000:0x00FC0000
         name=root
         at_pos=0x00040000
         colon_pos=0x00FC0000
         comma_pos=<NULL>
npartitions=2
        partition bootldr o=0 s=40000
        partition root o=40000 s=fc0000
parse_mtdpart: ret=2
Using Compaq bootldr partition definition
Creating 2 MTD partitions on "IPAQ flash":
0x00000000-0x00040000 : "bootldr"
mtd: Giving out device 0 to bootldr
0x00040000-0x01000000 : "root"
mtd: Giving out device 1 to root
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
IPv4 over IPv4 tunneling driver
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
mtdblock_open
ok
mtdblock_open
mtdblock_release
ok
mtdblock_open
jffs2_scan_eraseblock(): Node at 0x00c49b60 {0x1985, 0xe001, 0x0000002c)
has inv
alid CRC 0xd0f1565f (calculated 0xe0f1565f)
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b64:
0x002c in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b68:
0x565f in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b6c:
0x006e in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b70:
0x02cf in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b74:
0x020e in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b78:
0x1cee in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b7c:
0x0a04 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b80:
0xfb38 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c49b84:
0xa110 in
stead
Further such events for this erase block will not be printed
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c62194: Read
0x74205cf5
, calculated 0x74605cf5
jffs2_scan_dirent_node(): Name CRC failed on node at 0x00c62548: Read
0xd822375d
, calculated 0xd862375d
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c62acc: Read
0x3fbcb7db
, calculated 0x7fbcb7db
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c649d0: Read
0xdfdfd2af
, calculated 0xefdfd2af
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c6d094: Read
0x5c30089f
, calculated 0x536802f3
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c6d1c0: Read
0x5b160aa2
, calculated 0x5b560aa2
jffs2_scan_inode_node(): CRC failed on node at 0x00c6fc94: Read
0xf2200fb9, calc
ulated 0x48ad7fd9
jffs2_scan_inode_node(): CRC failed on node at 0x00c7005c: Read
0xdaee16a8, calc
ulated 0x70bc4dd0
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00c70240: Read
0x0b6e9c61
, calculated 0x1b6e9c61
jffs2_scan_inode_node(): CRC failed on node at 0x00c70594: Read
0xf43410b5, calc
ulated 0x3e7a3372
jffs2_scan_dirent_node(): Name CRC failed on node at 0x00c705d8: Read
0x62035508
, calculated 0xa2035508
Eep. Child "var" (ino #2223) of dir ino #1 doesn't exist!
Eep. Child "LC_MESSAGES" (ino #97) of dir ino #96 doesn't exist!
mtdblock_release
ok
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing init memory: 68K
Setting up RAMFS, please wait...
jffs2_read_inode(): No data nodes found for ino #80
jffs2_read_inode(): But it has children so we fake some modes for it
Setting up some devices
Executing /sbin/init...
INIT: version 2.78 booting
INIT: cannot execute "/etc/init.d/rcS"
INIT: Entering runlevel: 2
Calculating module dependencies... jffs2_read_inode(): No data nodes found
for i
no #55
jffs2_read_inode(): But it has children so we fake some modes for it
jffs2_read_inode(): No data nodes found for ino #57
jffs2_read_inode(): But it has children so we fake some modes for it
... failed: Input/output error
... failed: Input/output error
depmod: Can't open /lib/modules/2.4.18-rmk3/modules.dep for writing
done.
Loading modules: apm modprobe: could not parse modules.dep

h3600_ts modprobe: could not parse modules.dep

sa1100-rtc modprobe: could not parse modules.dep

h3600-sleeve modprobe: could not parse modules.dep

h3600_generic_sleeve modprobe: could not parse modules.dep

h3600-uda1341 modprobe: could not parse modules.dep

sa1100_cs modprobe: could not parse modules.dep

slhc modprobe: could not parse modules.dep

ppp_generic modprobe: could not parse modules.dep

ppp_async modprobe: could not parse modules.dep

Starting OpenBSD Secure Shell server: sshdstart-stop-daemon: open pidfile
/var/r
un/sshd.pid: Input/output error
.
Starting syslogd/klogd: start-stop-daemon: open pidfile
/var/run/syslogd.pid: In
put/output error
Starting PCMCIA services:rm: unable to stat `/var/run/pcmcia-scheme':
Input/outp
ut error
touch: /var/run/pcmcia-scheme: Input/output error
 modulesUsing /lib/modules/2.4.18-rmk3/pcmcia/pcmcia_core.o
Linux Kernel Card Services 3.1.22
  options: [pm]
Using /lib/modules/2.4.18-rmk3/pcmcia/sa1100_cs.o
<6>SA-1100 PCMCIA (CS release 3.1.22)
installing h3600_pcmcia_ops
sa1100_pcmcia_driver_init: pcmcia_low_level=c69325a4
sa1100_pcmcia_driver_init: skt=0 skt->virt_io=c6940000
sa1100_pcmcia_driver_init: skt=1 skt->virt_io=c6960000
sa1100_pcmcia_driver_init: done
Using /lib/modules/2.4.18-rmk3/pcmcia/ds.o
 cardmgr.
cardmgr[129]: watching 2 sockets
cardmgr[130]: starting, version is 3.2.3
cardmgr[130]: could not open /var/run/cardmgr.pid: Input/output error
cardmgr[130]: fopen(stabfile) failed: Input/output error
Starting Opie-login....

(none) login: opie-login: Respawning too fast -- going down

(none) login: root
Password:
Login incorrect

BusyBox on (none) login: root
Password:
Login incorrect

BusyBox on (none) login:

-- 
=================================================
Aaron Wadley                admin@cyberlizard.org
CyberLizard Industries        www.cyberlizard.org
=================================================