Brick-like

Hi,

I managed to install bootldr-pxa-2.20.4.bin on my brand new (only came
this morning!) HP5450. I was all excited after I'd installed the
task-bootstrap.jffs2.

Here's the scrollback from my serial terminal:

verifying ...
formatting ... done.
boot> boot
booting jffs2...
booting boot/zImage from partition >root<
Scanning all of flash for your JFFS2 convenience. Est Time: 6-12
seconds!
build_list: max = 01FBFFBC
.
dir entries = 0000035A
frag entries = 00000D59
+4 increments = 00000000
+file_offset increments = 000010B3
loaded file of size = 0x00094E18 at location 0xA0008000
kernel partition base A0008000
kernel_magic=E1A00000
kernel_region_words[9]=016F2818
Linux ELF flash_imgstart=50040000 size=01FC0000 dest=A0000000
offset=00008000
MMU Control=00000079
MMU PIDVAM=00000000
Skipping kernel copy by request.
A0008000: E1A00000
A0008004: E1A00000
A0008008: E1A00000
A000800C: E1A00000
A0008010: E1A00000
A0008014: E1A00000
A0008018: E1A00000
A000801C: E1A00000
A0008020: EA000002
A0008024: 016F2818
root_filesystem_name=ramdisk
Grabbed linuxargs, argc = 00000001
Using mach_type 000000DC
setting boot parameters to
 noinitrd root=/dev/mtdblock1 init=/linuxrc console=ttySA0
Making core tag at A0000100
Making cmdline tag at A0000114
Making mem32 tag at A00001B4
command line is:
mtdparts=ipaq:0x00040000_at_0x00000000(bootldr)ro,0x01FC0000_at_0x00
Disabling LCD controller
linuxEntryPoint=A0008000
Booting Linux image
CP15 r0=69052904
CP15 r1=00000079
CP15 r2=A39F4000
CP15 r3=FFFFFFFF
CP15 r5=00000007
CP15 r6=060805C0
CP15 r7=FFFFFFFF
CP15 r8=FFFFFFFF
CP15 r9=FFFFFFFF
CP15 r10=FFFFFFFF
CP15 r13=00000000
CP15 r14=FFFFBAFF
CP15 r15=FFFFFFFF
UFF
DABT
00000014
060805C0
UFF
DABT
00000014
FFF7EBBF

I waited a few minutes in case it was doing something silently, but it
seemed to have hung. Resetting it made it vibrate briefly, and I get the
following on the serial console:

&_start=00000000
FLASH_BASE=00000000
boot_flags_ptr=A39F3FFC
*boot_flags_ptr=00080015
boot_flags=00080015
                                                                                
enabling mmu
FLASH_BASE=00000000
 Evacuating 1MB of Flash to DRAM at: A3E00000
done
Map Flash virtual section to DRAM at: A3E00000
00000000 A3E00C0A
00000040 04000C02
00000080 08000C02
00000100 10000C02
00000140 14000C02
00000000 A3E00C0A
00000500 00000C02
00000A00 A0000C0A
00000A40 A4000C0A
00000E00 E0000C02
UFF
DABT
00000014
FFFFEFBF

I'd appreciate any advice on whether I've bricked it or not! If not, any
suggestions on how to proceed?

I see by the fact that there's a seperate HP5400 port project that it
perhaps wasn't as easy as I was imagining it would be!

Thanks in advance,

--
Ross