From: Hicks, Jamey (Jamey.Hicks@compaq.com)
Date: Thu Sep 13 2001 - 16:58:17 EDT
Try resetting it with center of joypad pushed? This defers boot until
the button is released, and is supposed to put it into interactive mode.
Also, try pushing the calendar (leftmost) button after it's booted.
Jamey
> -----Original Message-----
> From: Jean Meloche [mailto:jmeloche@avaya.com]
> Sent: Thursday, September 13, 2001 8:44 AM
> To: bootldr@handhelds.org
> Subject: [Bootldr] bootldr on monochrome iPAQ
>
>
> Hi!
>
> I have installed the
>
> Compaq OHH BootLoader, Rev 2-14-15 [BIG_KERNEL] [MONO]
>
> on my iPAQ 3150 but it refuses to accept commands on the serial port.
> I does report on the serial port as follows:
>
> U3
> @00000350
> F0100BEEF
>
> *MTST
> 00000001
> 00000002
> 00000004
> 00000008
> 00000010
> 00000020
> 00000040
> 00000080
> 00000100
> 00000200
> 00000400
> 00000800
> 00001000
> 00002000
> 00004000
> 00008000
> 00010000
> 00020000
> 00040000
> 00080000
> 00100000
> 00200000
> 00400000
> 00800000
> 01000000
> 02000000
> 04000000
> 08000000
> 10000000
> 20000000
> 40000000
> 80000000
> ENDM
> STKP
> C19F3FFC
> MMU table start=C19F4000
> Boot data start=C19F8000
> Boot data size=00008000
> Stack data base=C19F0000
> Stack data size=00004000
> FLASH_BASE=00000000
> Evacuating 1MB of Flash to DRAM at: C1E00000
> done
> Map Flash virtual section to DRAM at: C1E00000
> machine is mitsy
> verify flash size...
> btflash_init: mfrid=00000089
> devid=00000018
> walking flash descriptors (1x16)
> btflash_init: found flash 28F128J3A_1x16
> flashDescriptor=000174A8
> flashSectors=00017288
> nsectors=00000080
> flash_size=01000000
> flash_address_mask=00FFFFFF
> allocated partition_table
> defining partiton: bootldr
> defining partiton: params
> defining partiton: kernel
> dram_size: 01000000
> >> Compaq OHH BootLoader, Rev 2-14-15 [BIG_KERNEL] [MONO]
> >> Last link date: Mon Aug 20 15:15:01 PDT 2001
> >> Contact: bootldr@handhelds.org
>
> >> ARM Processor Rev=6901B116
> >> (c) 2000 Compaq Cambridge Research Laboratory
> Press Return to start the OS now, any other key for monitor menu
> DEBUG BOOT: not evaluating params
> DEBUG BOOT: use `params eval' to evaluate parameters.
>
>
>
> What can I do?
>
> Many thanks.
>
> --
> This message is intended only for the designated recipient(s). If you
> are not a designated recipient, you may not review, copy or distribute
> this message. If you receive this in error, please notify
> the sender by
> reply e-mail and delete this message. Thank you.
>
> jmeloche@avaya.com
> (908) 582-4894
> Jean Meloche
> _______________________________________________
> Bootldr mailing list
> Bootldr@handhelds.org
> http://handhelds.org/mailman/listinfo/bootldr
>
This archive was generated by hypermail 2.1.5 : Fri Jan 17 2003 - 17:47:02 EST