Re: X51V: Can't calibrate on first boot

I have a similar problem with an X50 however, my screen seems to be offset
to the right by about 1/2 inch. Thus wreaking havoc when attempting
calibration. I haven't had time to mess around with it and figure the
cause. Not sure if it's related to this problem or not but when the
crosshair displays in the upper left corner, how is it positioned: equally
spaced from the left and top? I've been able to just keep pressing on the
screen until calibration finishes however this is of little use since the
display is still offset to the right and the pointer isn't calibrated well.

On 6/23/07, 0xd34df00d <0xd34df00d_at_gmail.com> wrote

> By the way, I've managed to start only Xfbdev without anything on top
> of it (using ssh), and if I touch anywhere at the screen, the
> crosshair cursor always gets to the "very" top-left position.
>
> 2007/6/23, 0xd34df00d <0xd34df00d_at_gmail.com>:
> > 2007/6/23, Robert Martin <robertltux_at_gmail.com>:
> > > On 6/22/07, 0xd34df00d <0xd34df00d_at_gmail.com> wrote:
> > > > For me the sequence is upper left->upper right->lower right->lower
> > > > left->center. And I think that touching the screen several times to
> > > > get the crosshair moving is not OK, am I right?
> > > >
> > > > And what do you mean by firmware reload? I'm using Haret.
> > > >
> > > > 2007/6/23, Robert Martin <robertltux_at_gmail.com>:
> > > > > On 6/22/07, 0xd34df00d <0xd34df00d_at_gmail.com> wrote:
> > > > > > Hi all!
> > > > > >
> > > > > > I've followed the manual exactly, but when I try to calibrate my
> > > > > > screen (as prompted on first boot), I can't do it, because
> calibration
> > > > > > becames an infinite loop (after I press the crosshair in the
> center of
> > > > > > the screen, it moves back to it start position - top-left), so I
> can't
> > > > > > go further. And by the way, to get crosshair moving to any next
> > > > > > position, I should press (anywhere on the screen) five or six
> times.
> > > > > >
> > > > > > Thanks a lot and sorry for my English.
> > > > > >
> > > > > > --
> > > > > > --
> > > > > > _______________________________________________
> > > > > > Aximx50-port mailing list
> > > > > > Aximx50-port_at_handhelds.org
> > > > > > https://www.handhelds.org/mailman/listinfo/aximx50-port
> > > > > >
> > > > > what it should do is center upper left upper right lower left
> lower
> > > > > right > next the trick is you need to peg the crosshair in the
> center
> > > > > each time (there may be some sort of checksum to prevent a bad
> > > > > calibrate)
> > > > > if that doesn't work i would suggest doing a firmware reload
> > > > > --
> > > > > Robert L Martin
> > > > > --
> > > >
> > > a suggestion check to see if the axim works under the default os
> > > (leave the card out and then try it) also please put your responses
> > > below the previous postings
> > >
> > > --
> > > Robert L Martin
> > > --
> > > _______________________________________________
> > > Aximx50-port mailing list
> > > Aximx50-port_at_handhelds.org
> > > https://www.handhelds.org/mailman/listinfo/aximx50-port
> > >
> >
> > Axim works under the default os (win 5.0) just fine, everything is OK,
> > touchscreen handles clicks as they should be handled.
> >
> > --
> >
>
>
> --
> Whatever that doesn´t kill us today
> Tomorrow makes us stronger
>
> --
> _______________________________________________
> Aximx50-port mailing list
> Aximx50-port_at_handhelds.org
> https://www.handhelds.org/mailman/listinfo/aximx50-port
>
>
Received on Sat Jun 23 2007 - 16:21:58 EDT